Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame
Automaticky preložený názov:
Štandardná skúšobná metóda pre meranie porovnávacie Napaľovanie Charakteristika a Odolnosť proti prepáleniu z tuhého plastu za použitia 125 mm Flame
NORMA vydaná dňa 1.5.2014
Označenie normy: ASTM D5048-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2014
Kód tovaru: NS-29628
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Zápalnost a hořlavost materiálů a výrobků
Plastické hmoty obecně
Keywords:
burning characteristics, flammability, plastics, solid, resistance to burn-through, small-scale burning tests, vertical burning tests, ICS Number Code 13.220.40 (Ignitability and burning behaviour of materials and products), 83.080.01 (Plastics in general)
Significance and Use | ||||||||||||||
5.1 The test results represent afterflame plus afterglow time, in seconds, for a material under the conditions of the test. The test results for plaques also indicate whether or not the specified flame will burn through a material. 5.2 The effect of material thickness, colors, additives, deterioration, and possible loss of volatile components is measurable. 5.3 The burning characteristics vary with thickness. Compare test data with data for materials of similar thickness only. 5.4 The results serve as a reference for comparing the relative performance of materials and can be an aid in material selection. 5.5 In this test method, the specimens are subjected to specific laboratory test conditions. If different test conditions are substituted or the end-use conditions are changed, it will not always be possible by or from this test method to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire-test-exposure conditions described in this test method. |
||||||||||||||
1. Scope | ||||||||||||||
1.1 This fire-test-response test method covers a small-scale laboratory procedure for determining the relative burning characteristics and the resistance to burn-through of plastics using small bar and plaque specimens exposed to a 125-mm (500-W nominal) flame. 1.2 This test method was developed
for polymeric materials used for parts in devices and appliances.
The results are intended to serve as a preliminary indication of
their acceptability with respect to flammability for a particular
application. The final acceptance of the material is dependent upon
its use in complete equipment that conforms with the standards
applicable to such equipment.
1.3 The classification system described in 1.4 If found to be appropriate, it is suitable to apply the requirements to other nonmetallic materials. Such application is outside the scope of this technical committee. 1.5 This test method is not intended to cover plastics when used as materials for building construction or finishing. 1.6 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.7 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazards or fire risk assessment of materials, products, or assemblies under actual fire conditions. 1.8 This standard does not
purport to address all of the safety concerns, if any, associated
with its use. It is the responsibility of the user of this standard
to establish appropriate safety and health practices and determine
the applicability of regulatory limitations prior to use.
Standard Terminology Relating to
Plastics Standard Test Method for Measuring the
Comparative Burning Characteristics of Solid Plastics in a Vertical
Position (Includes all amendments and changes 9/11/2020). Standard Specification for Laboratory
Burner Used for Small-Scale Burning Tests on Plastic Materials
(Includes all amendments and changes 4/16/2020). Standard Practice for Confirmation of
20-mm (50-W) and 125-mm (500-W) Test Flames for Small-Scale Burning
Tests on Plastic Materials Standard Terminology of Fire
Standards Standard Practice for Conducting an
Interlaboratory Study to Determine the Precision of a Test
Method IEC?60695-11-20 Fire Hazard Testing-Part 11-20: Test
Flames - 500 W Flame Test Methods |
Historická
1.1.2010
Historická
1.11.2012
Historická
1.5.2014
Historická
1.8.2014
Historická
1.10.2009
Historická
1.5.2013
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.