Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Density and Relative Density of Crude Oils by Digital Density Analyzer
Automaticky preložený názov:
Štandardná skúšobná metóda pre hustoty a relatívnej hustoty surových olejov Digital Hustota Analyzer
NORMA vydaná dňa 1.10.2013
Označenie normy: ASTM D5002-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2013
Kód tovaru: NS-29467
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
crude oils , density, digital density analyzer, relative density, ICS Number Code 75.040 (Crude petroleum)
Significance and Use | ||||||||||||||||
5.1 Density is a fundamental physical property that can be used in conjunction with other properties to characterize the quality of crude oils. 5.2 The density or relative density of crude oils is used for the conversion of measured volumes to volumes at the standard temperatures of 15°C or 60°F and for the conversion of crude mass measurements into volume units. 5.3 The application of the density result obtained from this test method, for fiscal or custody transfer accounting calculations, can require measurements of the water and sediment contents obtained on similar specimens of the crude oil parcel. |
||||||||||||||||
1. Scope | ||||||||||||||||
1.1 This test method covers the determination of the density or relative density of crude oils that can be handled in a normal fashion as liquids at test temperatures between 15 and 35°C. This test method applies to crude oils with high vapor pressures provided appropriate precautions are taken to prevent vapor loss during transfer of the sample to the density analyzer. 1.2 This test method was evaluated in round robin testing using crude oils in the 0.75 to 0.95 g/mL range. Lighter crude oil can require special handling to prevent vapor losses. Heavier crudes can require measurements at higher temperatures to eliminate air bubbles in the sample. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. The accepted units of measurement of density are grams per millilitre and kilograms per cubic metre. 1.4 This standard does not
purport to address all of the safety concerns, if any, associated
with its use. It is the responsibility of the user of this standard
to establish appropriate safety and health practices and determine
the applicability of regulatory limitations prior to use.
Standard Practice for Automatic Sampling
of Petroleum and Petroleum Products (Includes all amendments and
changes 3/24/2023). Standard Practice for Manual Sampling of
Petroleum and Petroleum Products Standard Test Method for Density,
Relative Density, and API Gravity of Liquids by Digital Density
Meter Standard Guide for the Use of the Joint
API and ASTM Adjunct for Temperature and Pressure Volume Correction
Factors for Generalized Crude Oils, Refined Products, and
Lubricating Oils: API MPMS Chapter 11.1 (Includes all amendments
and changes 5/15/2020). Test Method for Density and Relative
Density (Specific Gravity) of Liquids by Lipkin Bicapillary
Pycnometer (Withdrawn 1993) Standard Test Method for Water in Crude
Oils by Potentiometric Karl Fischer Titration Standard Test Method for Density and
Relative Density (Specific Gravity) of Liquids by Bingham
Pycnometer Standard Specification for Reagent
Water |
Historická
1.6.2011
Historická
1.5.2011
Historická
1.11.2012
Historická
1.5.2010
Historická
1.12.2012
Historická
1.5.2014
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-12-22 (Počet položiek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.