Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D4985-10(2015)
Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA)
Automaticky preložený názov:
Štandardné špecifikácie pre Low silicate báze etylénglykolu chladiacej kvapaliny motora pre ťažké nákladné motory vyžadujúce Pre- obvinenia z doplnkového chladiacej látky ( SCA )
NORMA vydaná dňa 1.5.2015
Informácie o norme:
Označenie normy: ASTM D4985-10(2015)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2015
Kód tovaru: NS-590620
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Chladicí prostředky. Mrazicí prostředky. Mrazuvzdorné prostředky
Anotácia textu normy ASTM D4985-10(2015) :
Keywords:
coolant requiring SCA pre-charge, engine coolant, ethylene glycol, heavy duty engine coolant, heavy duty engine service, low silicate engine coolant, prediluted,, ICS Number Code 71.100.45 (Refrigerants and antifreezes)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification covers the requirements for low silicate ethylene glycol base engine coolants for cooling systems of heavy-duty engines. When concentrates are used at 40 to 60 % concentration by volume in water, or when prediluted glycol base engine coolants (50 volume % minimum) are used without further dilution, they will function effectively to provide protection against corrosion, freezing to at least −36.4°C (−33.5°F), and boiling to at least 108°C (226°F). Note 1: This specification is based on the knowledge of the
performance of engine coolants prepared from new or virgin
ingredients. A separate specification exists (Specification
D6210) for heavy-duty engine
coolants which may be prepared from recycled or reprocessed used
coolant or reprocessed industrial-source ethylene
glycol.
1.2 Coolants meeting this specification require an initial charge of a supplemental coolant additive (SCA) and require regular maintenance doses of an SCA to continue the protection in certain operating heavy-duty engine cooling systems, particularly those of the wet cylinder liner-in-block design. The SCA additions are defined by and are the primary responsibility of the engine manufacturer or vehicle manufacturer. If they provide no instructions, follow the SCA supplier's recommended instructions. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
