Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Determination of Additive Elements in Lubricating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry
Automaticky preložený názov:
Štandardná skúšobná metóda pre stanovenie prídavné prvky v mazacích olejov s indukčne viazanou plazmou atómovej emisnej spektrometrie
NORMA vydaná dňa 15.4.2009
Označenie normy: ASTM D4951-09
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.4.2009
Kód tovaru: NS-29262
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
additive-elements, barium, boron, calcium, copper, emission-spectrometry, ICP, inductively-coupled plasma atomic emission spectrometry, internal standard, lubricating oils, magnesium, molybdenum, phosphorus, sulfur, zinc, Additives--lubricating oils, Atomic absorption spectrometry (AAS), Barium content--petroleum products, Calcium content--petroleum products, Fuel sulfur, ICP-AES (inductively-coupled plasma atomic emission spectrometry), Lubricating oils, Magnesium content--petroleum products
Significance and Use | ||||||||||||||
This test method usually requires several minutes per sample. This test method covers eight elements and thus provides more elemental composition data than Test Method D 4628 or Test Methods D 4927. In addition, this test method provides more accurate results than Test Method D 5185, which is intended for used lubricating oils and base oils. Additive packages are blends of individual additives, which can act as detergents, antioxidants, antiwear agents, and so forth. Many additives contain one or more elements covered by this test method. Additive package specifications are based, in part, on elemental composition. Lubricating oils are typically blends of additive packages, and their specifications are also determined, in part, by elemental composition. This test method can be used to determine if additive packages and unused lubricating oils meet specifications with respect to elemental composition. |
||||||||||||||
1. Scope | ||||||||||||||
1.1 This test method covers the quantitative determination of barium, boron, calcium, copper, magnesium, molybdenum, phosphorus, sulfur, and zinc in unused lubricating oils and additive packages. 1.2 The precision statements are valid for dilutions in which the mass % sample in solvent is held constant in the range of 1 to 5 mass % oil. 1.3 The precision tables define the concentration ranges covered in the interlaboratory study. However, both lower and higher concentrations can be determined by this test method. The low concentration limits are dependent on the sensitivity of the ICP instrument and the dilution factor. The high concentration limits are determined by the product of the maximum concentration defined by the linear calibration curve and the sample dilution factor. 1.4 Sulfur can be determined if the instrument can operate at a wavelength of 180 nm. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||
2. Referenced Documents | ||||||||||||||
|
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.