Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D4863-13

Standard Test Method for Determination of Lubricity of Two-Stroke-Cycle Gasoline Engine Lubricants (Withdrawn 2022)

Automaticky preložený názov:

Štandardná skúšobná metóda pre stanovenie klzkosť dvojtaktné cyklu Mazivá benzínový motor

NORMA vydaná dňa 15.6.2013

Jazyk
Prevedenie	Elektronické PDF - 79.90 € Tlačené - 79.90 €
Dostupnosť	SKLADOM
Cena	79.90 € bez DPH
79.90 €

Informácie o norme:

Označenie normy: ASTM D4863-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.6.2013
Kód tovaru: NS-28936
Počet strán: 10
Približná hmotnosť: 30 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Maziva, průmyslové oleje a odpovídající výrobky

Anotácia textu normy ASTM D4863-13 :

Keywords:

ICS Number Code 75.100 (Lubricants, industrial oils and related products)

Doplňujúce informácie

Significance and Use

5.1 The oil in a two-stroke-cycle gasoline engine is either mixed with the fuel prior to use or is metered into the fuel supply at, or at some point prior to, its passage into the engine crankcase. The possibility of the amount of oil actually present in the engine being less than optimum always exists. Also, with some oil metering systems short periods of operation with less oil than desirable can occur when the power is increased suddenly. It has also been found that the incidence of piston scuff early in the life of the engine might be related to the lubricity of the oil used as defined by test procedures of this type.

1. Scope

1.1 This test method² evaluates the ability of lubricants to minimize piston and bore scuffing in two-stroke-cycle spark-ignition gasoline engines.

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D439-89	Specification for Automotive Gasoline (Withdrawn 1990)
D4858-13	Standard Test Method for Determination of the Tendency of Lubricants to Promote Preignition in Two-Stroke-Cycle Gasoline Engines (Withdrawn 2022)
E178-21	Standard Practice for Dealing With Outlying Observations
D6593-18e1	Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions (Includes all amendments and changes 6/22/2022).
D4857-12	Standard Test Method for Determination of the Ability of Lubricants to Minimize Ring Sticking and Piston Deposits in Two-Stroke-Cycle Gasoline Engines Other Than Outboards (Withdrawn 2021)
D2896-21	Standard Test Method for Base Number of Petroleum Products by Potentiometric Perchloric Acid Titration
D2885-21	Standard Test Method for Determination of Octane Number of Spark-Ignition Engine Fuels by On-Line Direct Comparison Technique
D2700-23b	Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel (Includes all amendments and changes 1/17/2024).
D2270-10(2016)	Standard Practice for Calculating Viscosity Index from Kinematic Viscosity at 40 °C and 100 °C
D874-23	Standard Test Method for Sulfated Ash from Lubricating Oils and Additives
D445-23	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
D664-18e2	Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration (Includes all amendments and changes 1/4/2019).
B152/B152M-19	Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar

Podobné normy:

ASTM D7317-07(2013)..

Historická
1.5.2013

ASTM D7320-13

Historická
1.10.2013

ASTM D7342-07

Historická
1.5.2007

ASTM D7373-12

Historická
1.6.2012

ASTM D7412-09

Historická
1.7.2009

ASTM D7414-09

Historická
1.7.2009

Odporúčame:

Aktualizácia zákonov

Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.