Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
Automaticky preložený názov:
Bežná prax pre lisovanie termoplastov do testovacích vzoriek plakov alebo listy
NORMA vydaná dňa 1.4.2016
Označenie normy: ASTM D4703-16
Dátum vydania normy: 1.4.2016
Kód tovaru: NS-635684
Počet strán: 13
Približná hmotnosť: 39 g (0.09 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
acrylonitrile-butadiene-styrene (ABS), chlorinated poly(vinyl chloride) (CPVC), compression molding, polyethylene (PE), poly(vinyl chloride) (PVC), styrene-butadiene, test specimen preparation, thermoplastics,, ICS Number Code 83.080.20 (Thermoplastic materials)
Significance and Use | ||||||||||
4.1 The methods by which sample materials are prepared and molded influence the mechanical properties of the specimen. Unlike injection molding, the objective of compression molding is to produce test specimens or sheets that are both homogeneous and isotropic. Specimens can be molded from powder or pellets such as are received directly from a material manufacturer, particles produced in a recycle recovery operation, or from a milled preform or sheet prepared on a two-roll mill. The powder, pellets, particles, preform, or sheet are melted and molded in a mold designed to produce a finished specimen of a given geometry, size, and thickness, or melted and molded in the form of a smooth plaque or sheet of uniform thickness from which desired specimens are cut, punched, or machined. Working a compound on a two-roll mill prior to molding will disperse and distribute the compound additives in a manner that will affect the physical properties of the compound. The relevant material specification or the material manufacturer shall be consulted to determine the need for milling a sample prior to compression molding. It is important to treat different samples of the same type of material in the same way: if milling was done prior to molding on a material which is to be used as a standard for comparison, all new materials to be tested against this practice shall be prepared and molded in a similar manner. 4.2 The apparatus and exact conditions required to prepare adequate specimens will usually vary for each plastic material. Apparatus and procedures satisfactory for molding many different plastic materials are given in this practice in Sections 5 and 6. The apparatus and procedures which have been found satisfactory for molding certain specific materials are given in the Appendixes. In any case, the specific apparatus and procedures to be used in producing compression-molded specimens of a given material shall be obtained by reference to the relevant material specification or by agreement between the purchaser and the supplier. |
||||||||||
1. Scope | ||||||||||
1.1 This practice covers the compression molding of thermoplastic granules and milled stock for the preparation of test specimens.2 1.2 While conditions for certain materials are given, the primary source of specific conditions shall be the material specification standards for each type of material. 1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1: The main body of this practice is equivalent to
ISO 293-1986. Annex A1 and
ISO 293-1986 differ in some details; however, specimens prepared
using Annex A1, Procedure A
should be equivalent to those prepared using ISO 293-1986, Cooling
Method D. Specimens prepared using Annex A1, Procedure C should be
equivalent to those prepared using ISO 293-1986, Cooling Method B.
However, due to the greater cooling rate tolerances of the ISO
standard, specimens prepared in accordance with ISO Cooling Method
B may not be equivalent to Annex
A1, Procedure C.
|
||||||||||
2. Referenced Documents | ||||||||||
|
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-01 (Počet položiek: 2 208 817)
© Copyright 2024 NORMSERVIS s.r.o.