Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D4688/D4688M-14(2021)e1
Standard Test Method for Evaluating Structural Adhesives for Finger Jointing Lumber (Includes all amendments and changes 4/20/2021).
NORMA vydaná dňa 15.4.2021
Informácie o norme:
Označenie normy: ASTM D4688/D4688M-14(2021)e1
Dátum vydania normy: 15.4.2021
Kód tovaru: NS-1022874
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D4688/D4688M-14(2021)e1 :
Keywords:
accelerated aging, billet, failure mode, finger joint, horizontal joint, structural joint, vertical joint,, ICS Number Code 83.180 (Adhesives)
Doplňujúce informácie
| Significance and Use | ||||||||
|
4.1?This test method is specifically designed to measure the performance of adhesives in finger joints manufactured under production line conditions. 4.1.1?The test method can be adapted to evaluate the adhesive performance of laboratory produced finger joints using commercial finger joint cutting heads with finger joints produced following the adhesive manufacturers recommendations. The conditions under which the finger joints were produced, including any limitations, are to be reported in 9.1.2.2 (see Note 2). Note 2:?If laboratory prepared finger joints are to be
produced, record details related to adhesive used, its preparation,
application to the cut finger joint, appropriate bonding parameters
and limitations in the production of the finger joint
assemblies.
4.2?The results of the test method may be used to certify an adhesive as suitable for finger jointing lumber under production line conditions where the intended end use of the finger jointed lumber may be in a variety of bonded structural wood products. 4.2.1?When the test results are to be used for certification of an adhesive a standard wood species shall be used. 4.2.1.1?Standard species may be found in Table 1 of Specification D2559. |
||||||||
| 1. Scope | ||||||||
|
1.1?This test method is designed to evaluate adhesives for finger jointing lumber used in the manufacture of a variety of bonded structural wood products such as structural glued laminated timber. It tests the tensile strength of joints under the following treatments: dry with no treatment, wet after one vacuum-pressure soak treatment, and wet after cyclic boil-dry treatment. 1.2?This test method is intended neither for quality control as the test assemblies are selected for the absence of defects usually found in run-of-the-mill finger joints nor as a substitute for in-plant qualification of end joints, including full-scale joint tests. Note 1:?This test method is specifically designed to evaluate
adhesives for use in finger jointing lumber using small scale test
specimens cut from carefully selected finger joint assemblies. In
contrast, plant qualification and quality control require tests of
full scale end joints selected randomly from production, designed
to evaluate parameters beyond adhesive performance which affect the
performance of the end use product.
1.3?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||
| 2. Referenced Documents | ||||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
