Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D4490-23
Standard Practice for the Use of Detector Tubes in the Measurement of Toxic Gases and Vapors
NORMA vydaná dňa 1.3.2023
Informácie o norme:
Označenie normy: ASTM D4490-23
Dátum vydania normy: 1.3.2023
Kód tovaru: NS-1137689
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D4490-23 :
Keywords:
air monitoring, detector tubes, dosimeter sampling, grab sampling, sampling and analysis, toxic gases and vapors, workplace atmospheres,, ICS Number Code 13.320 (Alarm and warning systems)
Doplňujúce informácie
| Significance and Use | ||
|
5.1?The Federal Occupational Safety and Health Administration, in 29 CFR 1910, designates that certain gases and vapors must not be present in workplace atmospheres at concentrations above specific values. 5.2?This practice will provide a means for the determination of airborne concentrations of certain gases and vapors given in 29 CFR 1910. 5.3?A partial list of chemicals for which this practice is applicable is presented in Annex A1. 5.4?This practice also provides for the sampling of gaseous atmospheres to be used for process control or other purposes (2, 24-23). 5.5?Advantages of the Detector Tube Method:? 5.5.1?As the detector tube method requires no chemical analyzers, external reagents, etc., advance preparations are not needed; detector tubes are always ready for use. 5.5.2?The detector tube method is well-suited for use at the work site because it is small, lightweight, and needs only a small sample volume to determine the concentration of gas or vapor in a sample. 5.5.3?The operating procedures are simple. 5.5.4?The results of measurements are available in just minutes, so fast action can be taken when needed. 5.5.5?Where no electrical power source is required, detector tubes can be used even when flammable gases are present. 5.5.6?Different types of detector tubes are available for different gases and measuring ranges, from 0.01 ppm to more than 10 %, depending on analyte and tube design, making the system flexible tor different sampling situations. |
||
| 1. Scope | ||
|
1.1?This practice covers the detection and measurement of concentrations of toxic gases or vapors using detector tubes (1, 2).2 A list of some of the gases and vapors that can be detected by this practice and their measurement ranges are provided in Annex A1. This list is given as a guide and should be considered neither absolute nor complete. 1.2?The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||
| 2. Referenced Documents | ||
|
Odporúčame:
Aktualizácia zákonov
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
