Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D4355/D4355M-14
Standard Test Method for Deterioration of Geotextiles by Exposure to Light, Moisture and Heat in a Xenon Arc Type Apparatus
Automaticky preložený názov:
Štandardná skúšobná metóda pre zhoršenie geotextíliou pôsobením svetla, vlhkosťou a teplom v type Xenon Arc Prístroje
NORMA vydaná dňa 15.7.2014
Informácie o norme:
Označenie normy: ASTM D4355/D4355M-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.7.2014
Kód tovaru: NS-26931
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D4355/D4355M-14 :
Keywords:
accelerated weathering, degradation, deterioration, geotextiles, solar radiation, xenon arc,, ICS Number Code 59.080.70 (Geotextiles)
Doplňujúce informácie
| Significance and Use | ||||||||||||||||||
|
5.1 This method is intended to induce property changes associated with end use conditions, including the effects of solar radiation, moisture and heat. The exposure used is not intended to simulate the deterioration caused by localized weather phenomena such as atmospheric pollution, biological attack, and salt water exposure. 5.2 The relation between time to failure in an exposure conducted in accordance with this test method, and service life in a specific outdoor environment requires determination of an acceleration factor as defined in Terminology G113. The acceleration factor is material-dependent and is only valid if it is based on data from a sufficient number of separate exterior and laboratory-accelerated exposures so that the results used to relate times to failure in each exposure can be analyzed using statistical methods. Note 1: An example of a statistical analysis using multiple
laboratory and exterior exposures to calculate an acceleration
factor is described by J. A. Simms.4
See Practice G151 for more
information and additional cautions about the use of acceleration
factors.
5.2.1 The deterioration curve obtained from the results of this test method enables the user to determine the tendency of a geotextile to deteriorate when exposed to xenon arc radiation, water and heat. 5.3 Variation in results may be expected when operating conditions are varied within the accepted limits of this test method. Its intended use is as a qualitative assessment of the presence of ultraviolet inhibitors, and comparison of that influence between products. However, no inference to the time of stability should be implied by the test results to the relation between time duration and outdoor exposure. Note 2: Information on sources of variability and on
strategies for addressing variability in the design, execution and
data analysis of laboratory accelerated exposure tests is found in
Guide G141.
5.3.1 If it becomes necessary for the purchaser and seller to use this test method for acceptance testing, the statistical bias, if any, between the purchaser's and seller's laboratories should be determined. Such comparison is based on specimens randomly drawn from the sample of geotextile being evaluated. 5.3.2 In such cases, as a minimum, the two parties should take a group of test specimens which are as homogeneous as possible, and which are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's 1.1 This test method covers the determination of the deterioration in tensile strength of geotextiles by exposure to xenon arc radiation, moisture, and heat. 1.2 The light and water exposure apparatus employs a xenon-arc light source. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||
|
Doporučujeme:
