Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D4293-22

Standard Specification for Phosphate Ester-Based Fluids for Turbine Lubrication and Steam Turbine Electro-Hydraulic Control (EHC) Applications

NORMA vydaná dňa 1.12.2022

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 57.60 € PDF + redline - ihneď - 69.10 € Tlačené - 57.60 € Tlač + redline - 69.10 €
Dostupnosť	SKLADOM
Cena	57.60 € bez DPH
57.60 €

Informácie o norme:

Označenie normy: ASTM D4293-22
Dátum vydania normy: 1.12.2022
Kód tovaru: NS-1100326
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Maziva, průmyslové oleje a odpovídající výrobky

Anotácia textu normy ASTM D4293-22 :

This specification covers the requirements for phosphate ester based fire resistant fluids for use in turbine lubrication. Only unused fluid is defined before it is installed in the turbine while fluids used in electrohydraulic control (EHC) systems is not. The use of this type of fluid is restricted to turbine systems that have been designed or modified to accommodate phosphate ester lubricants. Fire tests shall be performed which measure and describe the properties of the phosphate esters in response to heat and flame under controlled laboratory conditions and should not be considered or used for the description or appraisal of the fire hazard of the fluids under actual fire conditions.

Keywords:
ICS Number Code 75.100 (Lubricants, industrial oils and related products)

Doplňujúce informácie

1. Scope

1.1?This specification covers the minimum requirements for phosphate ester-based fluids for turbine lubricants and electro-hydraulic control fluids, as delivered.

1.2?The use of this type of fluid is restricted to turbine systems designed or modified to accommodate phosphate ester fluids.

1.3?This standard does not cover the minimum requirements for in-service phosphate ester fluids for the turbine electro-hydraulic control (EHC) fluid. These requirements are provided in Guide D8323.

1.4?The values stated in SI units are to be regarded as standard. For convenience, other units of measurement are provided in brackets.

1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

D92-18	Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester
IP510	Energy Institute StandardPetroleum ProductsDetermination of Organic Halogen ContentOxidative Microcoulometric Method
IEC60247	Insulating LiquidsMeasurement of Relative Permittivity, Dielectric Dissipation Factor (tan d) and d.c. Resistivity
EN14833	Petroleum and Related ProductsDetermination of the Hydraulic Stability of Fire Resistant Phosphate Ester Fluids
EN14832	Petroleum and Related ProductsDetermination of the Oxidation Stability and Corrosivity of Fire-resistant Phosphate Ester Fluids
D4057-22	Standard Practice for Manual Sampling of Petroleum and Petroleum Products
D3427-19	Standard Test Method for Air Release Properties of Hydrocarbon Based Oils
D2422-97(2018)	Standard Classification of Industrial Fluid Lubricants by Viscosity System
D1401-21	Standard Test Method for Water Separability of Petroleum Oils and Synthetic Fluids
D1298-12b(2017)e1	Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method (Includes all amendments and changes 3/14/2023).
D1169-19a	Standard Test Method for Specific Resistance (Resistivity) of Electrical Insulating Liquids (Includes all amendments and changes 10/10/2019).
D974-22	Standard Test Method for Acid and Base Number by Color-Indicator Titration
D892-23	Standard Test Method for Foaming Characteristics of Lubricating Oils
D664-18e2	Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration (Includes all amendments and changes 1/4/2019).
D445-23	Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
D130-19	Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
D97-17b(2022)	Standard Test Method for Pour Point of Petroleum Products (Includes all amendments and changes 11/29/2022).
D6304-20	Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration
D7546-24	Standard Test Method for Determination of Moisture in New and In-Service Lubricating Oils and Additives by Relative Humidity Sensor

Odporúčame:

Aktualizácia zákonov

Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.