ASTM C1516-05(2011)..
ASTM D6213-97(2009)..
ASTM D6662-13
ASTM E1730-09
ASTM E2110-11
ASTM E2134/E2134M-14..
Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D4016-14
Standard Test Method for Viscosity and Gel Time of Chemical Grouts by Rotational Viscometer (Laboratory Method) (Withdrawn 2023)
Automaticky preložený názov:
Štandardná skúšobná metóda pre viskozita a Gél Time chemických zálievky rotačného viskozimetra (Laboratory Method)
NORMA vydaná dňa 15.6.2014
Informácie o norme:
Označenie normy: ASTM D4016-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.6.2014
Kód tovaru: NS-25736
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D4016-14 :
Keywords:
chemical grout, coefficient of viscosity, gel point, grouting, Newtonian fluids, non-Newtonian fluids, rotational viscometer, viscosity, ICS Number Code 91.100.99 (Other construction materials)
Doplňujúce informácie
| Significance and Use | ||||||||
|
5.1 This test is intended for materials that will penetrate soil voids and rock fissures. Viscosity alone is not necessarily an exact index of grout penetrability. |
||||||||
| 1. Scope | ||||||||
|
1.1 This test method covers the determination of viscosity of catalyzed chemical grouts with a rotational viscometer (laboratory method), over the range from 1.0 mPa·s to 1000 mPa·s (1.0 to 1000 cP). 1.2 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026. 1.2.1 The procedures used to specify how data are collected/recorded or calculated, in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose of obtaining the data, special purpose studies, or any consideratons for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design. 1.3 The values stated in SI units are the standard. Other units provided in parentheses are for the convenience of the user. 1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||
| 2. Referenced Documents | ||||||||
|
Podobné normy:
Historická
1.12.2011
Historická
1.6.2009
Historická
1.6.2013
Historická
1.11.2009
Historická
1.11.2011
Historická
1.4.2014
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
