Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced Plastic Rod
Automaticky preložený názov:
Štandardná skúšobná metóda pre mechanické vlastnosti ťahané sklenými vláknami vystuženého plastu Rod
NORMA vydaná dňa 1.3.2008
Označenie normy: ASTM D3916-08
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2008
Kód tovaru: NS-25330
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
glass reinforced plastic, pultruded rods, tensile properties, Glass-fiber-reinforced (GRP) plastics, Plastic glass-fiber-reinforced pultruded rod, Reinforced plastics, Reinforced thermosetting plastics (RTP), Tensile properties/testing--plastics, ICS Number Code 83.120 (Reinforced plastics)
Significance and Use | ||||||||
The high axial-tensile strength and the low transverse-compressive strength of pultruded rod combine to present some unique problems in determining the tensile strength of this material with conventional test grips. The high transverse-compressive forces generated in the conventional method of gripping tend to crush the rod, thereby causing premature failure. In this test method, aluminum-alloy tabs contoured to the shape of the rod reduce the compressive forces imparted to the rod, thus overcoming the deleterious influence of conventional test grips. Tensile properties are influenced by specimen preparation, strain rate, thermal history, and the environmental conditions at the time of testing. Consequently, where precise comparative results are desired, these factors must be carefully controlled. Tensile properties provide useful data for many engineering design purposes. However, due to the high sensitivity of these properties to strain rate, temperature, and other environmental conditions, data obtained by this test method should not, by themselves, be considered for applications involving load-time scales or environmental conditions that differ widely from the test conditions. In cases where such dissimilarities are apparent, the sensitivities to strain rate, including impact and creep, as well as to environment, should be determined over a wide range of conditions as dictated by the anticipated service requirements. |
||||||||
1. Scope | ||||||||
1.1 This test method describes a procedure for determining the tensile properties of pultruded, glass-fiber-reinforced thermosetting plastic rod of diameters ranging from 3.2 mm (1/8 in.) to 25.4 mm (1 in.). Little test specimen preparation is required; however, reusable aluminum tab grip adapters (Fig. 1) of appropriate size are required to prevent premature failure of the specimens at the grips. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Note 3 and Note 4. Note 1—There is no known ISO equivalent to this test method. |
||||||||
2. Referenced Documents | ||||||||
|
Historická
1.1.2011
Historická
1.5.2013
Historická
1.8.2011
Historická
1.4.2012
Historická
1.10.2013
Historická
1.8.2012
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.