Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM D3903-03(2007) 1.11.2007 náhľad

Doplňujúce informácie

ASTM D3903-03(2007)

Standard Specification for Rubber Seals Used in Air-Heat Transport of Solar Energy Systems

Automaticky preložený názov:

Štandardné špecifikácie pre gumové tesnenie používaných v leteckej-transport tepla solárne energetické systémy

NORMA vydaná dňa 1.11.2007

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 60.90 € Tlačené - 60.90 €
Dostupnosť	SKLADOM
Cena	60.90 € bez DPH
60.90 €

Informácie o norme:

Označenie normy: ASTM D3903-03(2007)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.11.2007
Kód tovaru: NS-25289
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM D3903-03(2007) :

Keywords:
air-heat transport, rubber seals, solar energy systems, Air-heat transport devices (solar), Rubber--specifications, Rubber seals--specifications, Solar heating/cooling systems--specifications, Solar materials/applications--specifications, ICS Number Code 21.140 (Seals, glands)

Doplňujúce informácie

1. Scope

1.1 This specification covers the general requirements for the rubber seals used in solar energy systems employing air-heat transport. Examples are duct and damper seals. Particular applications may necessitate other requirements that would take precedence over these requirements when specified.

Note 1—Rubber seals for the collector are covered in Specifications D 3667 and D 3771.

1.2 Design requirement pertains only to permissible deflections of the rubber during thermal expansion or contraction of the seal in use and the tolerances in dimensions of molded and extruded seals.

1.3 This specification does not include requirements pertaining to the fabrication or installation of the seals.

1.4 The values stated in SI units are to be regarded as the standard.

1.5 The following safety hazards caveat pertains only to the test methods portion, Section 10, of this specification: This standard does not purport to address the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D1149-18	Standard Test Methods for Rubber Deterioration´Cracking in an Ozone Controlled Environment
D1229-03(2019)	Standard Test Method for Rubber Property´Compression Set at Low Temperatures
D1349-14(2019)	Standard Practice for Rubber´Standard Conditions for Testing
D1415-18	Standard Test Method for Rubber Property´International Hardness
D1566-21a	Standard Terminology Relating to Rubber (Includes all amendments and changes 11/10/2021).
D2137-11(2018)	Standard Test Methods for Rubber Property´Brittleness Point of Flexible Polymers and Coated Fabrics
D2240-15(2021)	Standard Test Method for Rubber Property—Durometer Hardness
D3182-21a	Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets (Includes all amendments and changes 11/12/2021).
D3183-10(2019)	Standard Practice for Rubber´Preparation of Pieces for Test Purposes from Products
D3667-16(2022)	Standard Specification for Rubber Seals Used in Flat-Plate Solar Collectors
D3771-15(2022)	Standard Specification for Rubber Seals Used in Concentrating Solar Collectors
G7-05	Standard Practice for Atmospheric Environmental Exposure Testing of Nonmetallic Materials
G151-19	Standard Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources
G155-21	Standard Practice for Operating Xenon Arc Lamp Apparatus for Exposure of Materials

D412-16(2021)	Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
D865-11(2018)	Standard Test Method for Rubber´Deterioration by Heating in Air (Test Tube Enclosure)
D395-18	Standard Test Methods for Rubber Property´Compression Set
C719-22	Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)
C661-15(2022)	Standard Test Method for Indentation Hardness of Elastomeric-Type Sealants by Means of a Durometer
C717-19	Standard Terminology of Building Seals and Sealants

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.