Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Color and Strength of Chromatic Pigments with a Mechanical Muller
Automaticky preložený názov:
Štandardná skúšobná metóda pre farby a sila farebné pigmenty s mechanickým Muller
NORMA vydaná dňa 1.2.2008
Označenie normy: ASTM D387-00(2008)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.2.2008
Kód tovaru: NS-25156
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
chromatic pigment, color, muller, Color--paints/related coatings/materials, Pigments (general properties), Tinting strength, Muller device, ICS Number Code 87.060.10 (Pigments and extenders)
Significance and Use | ||||||||||||||||
Color and tinting strength are the most important properties of a color pigment. This test method provides a means of testing these properties for quality control. This test method is intended as a referee method so that such matters as the vehicle for preparing the dispersions and the white for making tints have been suggested. However, other vehicles and whites may be suitable for quality control purposes, and changes in this test method are allowed by agreement between the parties to a test. It is assumed that the most exact comparison of mass color and tinting strength occurs when the pigment is completely dispersed. By following the procedure described in Annex A1, the conditions for achieving the maximum practical degree of dispersion with a mechanical muller may be determined. Color and strength tests should be carried out under these conditions. The results obtained with a mechanical muller do not necessarily correlate directly with an industrial situation where different dispersing conditions exist. However, dispersion with a mechanical muller is a quick and inexpensive way of testing the color and strength of a pigment for routine quality control. |
||||||||||||||||
1. Scope | ||||||||||||||||
1.1 This test method is intended to be used to compare the color and strength of a pigment under test with a reference standard of the same type and grade. 1.2 This test method does not apply to white pigments. Note 1—Test Method D 3022 is similar to this test method, but it utilizes a miniature sandmill rather than a mechanical muller, to disperse the chromatic pigment. Note 2—Test Method D 332 and Test Method D 2745 are similar to this test method, but they are intended for use with white pigments, rather than chromatic pigments. 1.3 The values stated in SI units are the preferred unit of measurement. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 8. |
||||||||||||||||
2. Referenced Documents | ||||||||||||||||
|
Historická
15.4.2012
Historická
1.11.2013
Historická
1.6.2012
Historická
1.6.2011
Historická
1.6.2009
Historická
1.7.2009
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-22 (Počet položiek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.