Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM D3786/D3786M-13 1.1.2013 náhľad

Doplňujúce informácie

ASTM D3786/D3786M-13

Standard Test Method for Bursting Strength of Textile Fabrics´Diaphragm Bursting Strength Tester Method

Automaticky preložený názov:

Štandardná skúšobná metóda pre pevnosť v tlaku textilných Fabrics'Diaphragm roztrhnutiu Tester Sila metódy

NORMA vydaná dňa 1.1.2013

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 70.20 € Tlačené - 70.20 €
Dostupnosť	SKLADOM
Cena	70.20 € bez DPH
70.20 €

Informácie o norme:

Označenie normy: ASTM D3786/D3786M-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.1.2013
Kód tovaru: NS-24874
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Textilní tkaniny

Anotácia textu normy ASTM D3786/D3786M-13 :

Keywords:

diaphragm bursting pressure, knitted fabric, non woven fabric, ICS Number Code 59.080.30 (Textile fabrics)

Doplňujúce informácie

Significance and Use

5.1 This method for the determination of diaphragm bursting strength of knitted, nonwoven and woven fabrics is being used by the textile industry for the evaluation of a wide variety of end uses.

5.2 In cases where test results obtained using the procedures in Test Method D3786 have not been correlated with actual performance, Test Method D3786 is considered satisfactory for acceptance testing of commercial shipments of textile fabrics for bursting strength since the method has been used extensively in the trade for acceptance testing. In cases where disagreement arising from differences in values reported by the purchaser and the supplier when using Test Method D3786 for acceptance testing, the statistical bias, if any, between the laboratory of the purchaser and the laboratory of the supplier should be determined with comparison based on testing specimens randomly drawn from one sample of material of the type being evaluated.

1.1 This test method describes the measurement of the resistance of textile fabrics to bursting using a hydraulic or pneumatic diaphragm bursting tester. This test method is generally applicable to a wide variety of textile products.

1.2 This test method may also be applicable for stretch woven and woven industrial fabrics such as inflatable restraints.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

TAPPI Method T 403	, Bursting Strength of Paper Available from Technical Association of the Pulp and Paper Industry (TAPPI), 15 Technology Parkway South, Norcross, GA 30092, http://www.tappi.org.
D4850-23	Standard Terminology Relating to Fabrics and Fabric Test Methods
D1776-08	Standard Practice for Conditioning and Testing Textiles
D3787-16(2020)	Standard Test Method for Bursting Strength of Textiles´Constant-Rate-of-Traverse (CRT) Ball Burst Test
D123-23	Standard Terminology Relating to Textiles