Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D3679-21

Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding

NORMA vydaná dňa 1.9.2021

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 77.60 € Tlačené - 77.60 €
Dostupnosť	SKLADOM
Cena	77.60 € bez DPH
77.60 €

Informácie o norme:

Označenie normy: ASTM D3679-21
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.9.2021
Kód tovaru: NS-1036252
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Termoplasty

Anotácia textu normy ASTM D3679-21 :

Keywords:

plastic building products, plastic weatherability, recycled plastic, rigid PVC siding, specification,, ICS Number Code 83.080.20 (Thermoplastic materials)

Doplňujúce informácie

1. Scope

1.1?This specification establishes requirements and test methods for the materials, dimensions, warp, shrinkage, impact strength, expansion, appearance, and wind load resistance of extruded single-wall siding manufactured from rigid (unplasticized) PVC compound. Methods of indicating compliance with this specification are also provided.

1.2?The use PVC recycled plastic in this product shall be in accordance with the requirements in Section 4.

1.3?Rigid (unplasticized) PVC soffit is covered in Specification D4477.

1.4?Siding produced to this specification shall be installed in accordance with Practice D4756. Reference shall also be made to the manufacturer's installation instructions for the specific product to be installed.

Note 1:?Information with regard to siding maintenance shall be obtained from the manufacturer.

1.5?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6?The following precautionary caveat pertains to the test method portion only, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 2:?There is no known ISO equivalent to this standard.

1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

D5947-18	Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
D2457-21	Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
D3892-15(2020)	Standard Practice for Packaging/Packing of Plastics
E631-15	Standard Terminology of Building Constructions
E1753-22	Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films
G147-17	Standard Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests
ASCE?7-02	Minimum Design Loads for Buildings and Other Structures Available from American Society of Civil Engineers (ASCE), 1801 Alexander Bell Dr., Reston, VA 20191, http://www.asce.org.
D5033-00	Standard Guide for Development of ASTM Standards Relating to Recycling and Use of Recycled Plastics (Withdrawn 2007)
D4756-15	Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit
D4477-22	Standard Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit
D4226-19e1	Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products (Includes all amendments and changes 8/21/2020).
D618-21	Standard Practice for Conditioning Plastics for Testing
D635-22	Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position
D696-16	Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between -30°C and 30°C with a Vitreous Silica Dilatometer
D883-24	Standard Terminology Relating to Plastics
D1435-20	Standard Practice for Outdoor Weathering of Plastics
D5206-19	Standard Test Method for Windload Resistance of Rigid Plastic Siding
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D2244-23	Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
D1042-22	Standard Test Method for Linear Dimensional Changes of Plastics Caused by Exposure to Heat and Moisture

Odporúčame:

EviZak - všetky zákony vrátane ich evidencie na jednom mieste

Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !

Chcete vedieť viac informácii ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.