Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM D3667-05(2010) 1.6.2010 náhľad

Doplňujúce informácie

ASTM D3667-05(2010)

Standard Specification for Rubber Seals Used in Flat-Plate Solar Collectors

Automaticky preložený názov:

Štandardné špecifikácie pre gumové tesnenie sa používajú pre ploché-doskové slnečné kolektory

NORMA vydaná dňa 1.6.2010

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 70.20 € Tlačené - 70.20 €
Dostupnosť	SKLADOM
Cena	70.20 € bez DPH
70.20 €

Informácie o norme:

Označenie normy: ASTM D3667-05(2010)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.6.2010
Kód tovaru: NS-24401
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Těsnění, ucpávky

Anotácia textu normy ASTM D3667-05(2010) :

Keywords:

flat-plate solar collectors, preformed seals, rubber, sealing compounds, Flat-plate solar collectors, Rubber--specifications, Rubber seals--specifications, Solar collectors--specifications, Solar heating/cooling systems--specifications, Solar materials/applications--specifications, ICS Number Code 21.140 (Seals, glands)

Doplňujúce informácie

1. Scope

1.1 This specification covers the general requirements for materials used in rubber seals of flat-plate solar collectors, except vertically mounted passive collectors. Particular applications may necessitate other requirements that would take precedence over these requirements when specified.

1.2 The design requirement pertains only to permissible deflections of the rubber during thermal expansion or contraction of the seal in use and the tolerances in dimensions of molded and extruded seals.

1.3 This specification does not include requirements pertaining to the fabrication or installation of the seals.

Note 1—Practices G151 and G155 are performance-based practices that replace Practice cited in previous versions of D3667. Practice described very specific designs for devices used for xenon arc exposure. The apparatus described in Practice is covered by the practices that replace it.

1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5 The following safety hazards caveat pertains only to Section 9, Test Methods, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

G155-21	Standard Practice for Operating Xenon Arc Lamp Apparatus for Exposure of Materials
G151-19	Standard Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources
D1349-14(2019)	Standard Practice for Rubber´Standard Conditions for Testing
C717-19	Standard Terminology of Building Seals and Sealants
C719-22	Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)
D395-18	Standard Test Methods for Rubber Property´Compression Set
D412-16(2021)	Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
D865-11(2018)	Standard Test Method for Rubber´Deterioration by Heating in Air (Test Tube Enclosure)
D1149-18	Standard Test Methods for Rubber Deterioration´Cracking in an Ozone Controlled Environment
D1229-03(2019)	Standard Test Method for Rubber Property´Compression Set at Low Temperatures
C661-15(2022)	Standard Test Method for Indentation Hardness of Elastomeric-Type Sealants by Means of a Durometer
D2137-11(2018)	Standard Test Methods for Rubber Property´Brittleness Point of Flexible Polymers and Coated Fabrics
D2240-15(2021)	Standard Test Method for Rubber Property—Durometer Hardness
D1415-18	Standard Test Method for Rubber Property´International Hardness
D1566-21a	Standard Terminology Relating to Rubber (Includes all amendments and changes 11/10/2021).
D3182-21a	Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets (Includes all amendments and changes 11/12/2021).
D3183-10(2019)	Standard Practice for Rubber´Preparation of Pieces for Test Purposes from Products
G7-05	Standard Practice for Atmospheric Environmental Exposure Testing of Nonmetallic Materials
RMA Handbook