Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Practice for Calculating Heat Value, Compressibility Factor, and Relative Density of Gaseous Fuels
Automaticky preložený názov:
Štandardné praktiky pre výpočet výhrevnosti, stlačiteľnosti faktor, a relatívna hustota plynných palív
NORMA vydaná dňa 1.11.2011
Označenie normy: ASTM D3588-98(2011)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.11.2011
Kód tovaru: NS-24142
Počet strán: 9
Približná hmotnosť: 27 g (0.06 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
, Calculating test values, Calorific value, Carbureted water gas, Coal gas, Coal products, Coke oven gas, Compressibility, Dry natural gas, Gaseous fuels, Manufactured gas, Natural gas service systems, Propane, Reformed natural gas, Relative density, Retort coal gas, Specific gravity--petroleum products, Utility gaseous fuels, ICS Number Code 75.160.30 (Gaseous fuels)
Significance and Use | ||||||||||||||||
The heating value is a measure of the suitability of a pure gas or a gas mixture for use as a fuel; it indicates the amount of energy that can be obtained as heat by burning a unit of gas. For use as heating agents, the relative merits of gases from different sources and having different compositions can be compared readily on the basis of their heating values. Therefore, the heating value is used as a parameter for determining the price of gas in custody transfer. It is also an essential factor in calculating the efficiencies of energy conversion devices such as gas-fired turbines. The heating values of a gas depend not only upon the temperature and pressure, but also upon the degree of saturation with water vapor. However, some calorimetric methods for measuring heating values are based upon the gas being saturated with water at the specified conditions. The relative density (specific gravity) of a gas quantifies the density of the gas as compared with that of air under the same conditions. |
||||||||||||||||
1. Scope | ||||||||||||||||
1.1 This practice covers procedures for calculating heating value, relative density, and compressibility factor at base conditions (14.696 psia and 60°F (15.6°C)) for natural gas mixtures from compositional analysis. It applies to all common types of utility gaseous fuels, for example, dry natural gas, reformed gas, oil gas (both high and low Btu), propane-air, carbureted water gas, coke oven gas, and retort coal gas, for which suitable methods of analysis as described in Section 6 are available. Calculation procedures for other base conditions are given. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||
2. Referenced Documents | ||||||||||||||||
|
Historická
1.11.2012
Historická
1.5.2013
Historická
1.11.2012
Historická
1.12.2008
Historická
1.11.2013
Historická
1.11.2011
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-12-23 (Počet položiek: 2 217 157)
© Copyright 2024 NORMSERVIS s.r.o.