Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for Perfluoroalkoxy (PFA) Resin Molding and Extrusion Materials
NORMA vydaná dňa 1.9.2021
Označenie normy: ASTM D3307-21
Dátum vydania normy: 1.9.2021
Kód tovaru: NS-1036250
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
This specification covers melt processable molding and extrusion materials of PFA-perfluoro(alkoxy alkane) fluorocarbon resin. The materials are copolymers of TFE-fluorocarbon resins containing perfluoroalkoxy side chains. This specification is intended to provide a means for calling out plastic materials used in the fabrication of end items or parts. This specification covers 13 types of PFA-fluorocarbon resins supplied in pellet form for molding and extrusion. The materials shall be of uniform composition and so prepared as to conform to the requirements specified. Conditioning, melt flow rate, melting endotherm peak temperature, specific gravity, tensile properties, and dielectric constant and dissipation factor tests shall be performed to conform with the requirements specified.
Keywords:
extrusion, injection molding, fluoropolymer, perfluoroalkoxy, PFA-fluorocarbon resin, tetrafluoroethylene copolymer, TFE-fluorocarbon,, ICS Number Code 83.140.99 (Other rubber and plastic products)
1. Scope | ||||||||||||||||||||||||||||
1.1?This specification covers melt processable molding and extrusion materials of Perfluoroalkoxy (PFA) resin. The materials are copolymers of tetrafluoroethylene and perfluoroalkoxy. 1.2?This specification is intended to provide a means for calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this specification. 1.3?This specification does not cover recycled plastics. 1.4?The values stated in SI units2 are to be regarded as standard. The values given in parentheses are for information only. 1.5?The following precautionary caveat pertains only to the test methods portions, Sections 8 and 9 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1:?This specification, ISO 20568-1, and ISO 20568-2
differ in approach or detail. Data obtained using either may not be
technically equivalent.
1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||
|
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-12-22 (Počet položiek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.