Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D3138-21
Standard Specification for Solvent Cements for Transition Joints Between Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Non-Pressure Piping Components
NORMA vydaná dňa 1.11.2021
Informácie o norme:
Označenie normy: ASTM D3138-21
Dátum vydania normy: 1.11.2021
Kód tovaru: NS-1043759
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D3138-21 :
This specification provides general requirements for solvent cements used in joining acrylonitrile-butadiene-styrene (ABS) plastic pipe or fittings to poly(vinyl chloride) (PVC) plastic pipe or fittings in non-pressure applications only. The solvent cement shall be a solution of Class 12454-B, unplasticized poly(vinyl chloride) molding or extrusion compound. Materials shall be tested and the individual grades shall conform to specified values of resin content, dissolution, viscosity, lap shear strength, hydrostatic burst strength, solids content, and bond strength.
Keywords:
ICS Number Code 83.180 (Adhesives)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||||
|
1.1?This specification provides general requirements for solvent cements used in joining acrylonitrile-butadiene-styrene (ABS) plastic pipe or fittings to poly(vinyl chloride) (PVC) plastic pipe or fittings. 1.2?These cements are intended for use in cementing transition joints between ABS and PVC materials in non-pressure applications only (25 psi (170 kPa) or less). Note 1:?This specification was developed to provide a means
for joining an ABS non-pressure piping system using a
solvent-cemented transition joint, for example, joining ABS
building drain to a PVC sewer system. The intention was not to
create a specification for an all purpose ABS-PVC solvent cement
that would be used for mixing of ABS and PVC piping materials nor
to specify a cement that could generally be used for either
material. Specific cements for ABS or PVC components should be used
(see 1.3).
1.3?Solvent cements used for joining PVC pipe and fittings are specified in Specification D2564. Solvent cements used for joining ABS pipe and fittings are specified in Specification D2235. 1.4?A recommended procedure for joining ABS to PVC pipe and fittings for non-pressure applications is given in the appendix. 1.5?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6?The following safety hazards caveat pertains only to the test methods portion, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
