Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D3106-07(2018)
Standard Test Method for Permanent Deformation of Elastomeric Yarns
NORMA vydaná dňa 1.7.2018
Informácie o norme:
Označenie normy: ASTM D3106-07(2018)
Dátum vydania normy: 1.7.2018
Kód tovaru: NS-856418
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D3106-07(2018) :
Keywords:
deformation, elastomeric, yarn,, ICS Number Code 59.080.20 (Yarns)
Doplňujúce informácie
| Significance and Use | ||||||
|
5.1 Test Method D3106 for testing permanent deformation of elastomeric yarns is considered satisfactory for acceptance testing of commercial shipments when there is prior agreement as to the exact value of elongation to be used for testing, since current estimates of between-laboratory precision are acceptable. 5.1.1 If there are differences or practical significance between reported test results for two laboratories (or more) comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, test samples that are as homogeneous as possible, drawn from the material from which the disparate test results were obtained, and randomly assigned in equal numbers to each laboratory for testing. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias. 5.2 Yarns are subjected to long periods of tension resulting in an appreciable amount of stretch during normal use. A portion of the induced stretch may be permanent. The amount of permanent deformation is influenced by the amount of tension, the time the yarn is under tension and the time available for recovery between successive uses. 5.3 For optimum processing of elastomeric yarns, the permanent deformation value should be low or zero. |
||||||
| 1. Scope | ||||||
|
1.1 This test method covers the determination of the permanent deformation of bare, continuous elastomeric monofilaments and filament yarns made from rubber, spandex, anidex, or other elastomers subjected to prolonged periods of tension. This test method is applicable to elastomeric yarns having a linear density in the range from 4 to 320 tex (36 to 2900 den.). 1.2 This test method is not applicable to covered, wrapped, core-spun yarns, or yarns spun from elastomeric staple. 1.3 This test method was developed using yarns in the “as-received” condition, but may be used for treated yarns provided the treatment is specified. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||
| 2. Referenced Documents | ||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
