Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D2454-18

Standard Practice for Determining the Effect of Overbaking on Organic Coatings

NORMA vydaná dňa 1.7.2018

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 60.90 € Tlačené - 60.90 €
Dostupnosť	SKLADOM
Cena	60.90 € bez DPH
60.90 €

Informácie o norme:

Označenie normy: ASTM D2454-18
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.7.2018
Kód tovaru: NS-854203
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Technologie nátěrů

Anotácia textu normy ASTM D2454-18 :

Keywords:
effect of overbake, organic coatings, overbake,, ICS Number Code 87.020 (Paint coating processes)

Doplňujúce informácie

Significance and Use

5.1 Most coatings are designed for a specific baking time and temperature. For a variety of reasons (line stoppages, rerouting back through ovens, oven overheating, etc.) the prescribed time or temperature, or both, of the bake is often exceeded. This practice has been found to be useful in evaluating the effects of overbakes on coatings.

1. Scope

1.1 This practice covers the determination of the time-temperature effect of overbaking on the physical and chemical properties of organic coatings.

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

D2201-23	Standard Practice for Preparation of Zinc-Coated and Zinc-Alloy-Coated Steel Panels for Testing Paint and Related Coating Products
D1005-95(2020)	Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
D823-18(2022)	Standard Practices for Producing Films of Uniform Thickness of Paint, Coatings and Related Products on Test Panels
D523-14(2018)	Standard Test Method for Specular Gloss
D522-93a(2001)	Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings
E805-22	Standard Practice for Identification of Instrumental Methods of Color or Color-Difference Measurement of Materials
D2794-93(2024)	Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
D609-17(2022)	Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products
D1308-20	Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Coating Systems
D1729-22	Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials
D1730-09(2020)	Standard Practices for Preparation of Aluminum and Aluminum-Alloy Surfaces for Painting
D1731-09(2020)	Standard Practices for Preparation of Hot-Dip Aluminum Surfaces for Painting
D2244-23	Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
D3359-23	Standard Test Methods for Rating Adhesion by Tape Test
D3363-22	Standard Test Method for Film Hardness by Pencil Test
D6386-22	Standard Practice for Preparation of Zinc (Hot-Dip Galvanized) Coated Iron and Steel Product and Hardware Surfaces for Painting
D7091-22	Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals
D7396-14(2020)	Standard Guide for Preparation of New, Continuous Zinc-Coated (Galvanized) Steel Surfaces for Painting
D1640-03	Standard Test Methods for Drying, Curing, or Film Formation of Organic Coatings at Room Temperature
D2197-16(2022)	Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.