Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D2440-13

Standard Test Method for Oxidation Stability of Mineral Insulating Oil

Automaticky preložený názov:

Štandardná skúšobná metóda pre oxidačnej stability minerálne izolačné oleje

NORMA vydaná dňa 1.2.2013

Jazyk
Prevedenie	Elektronické PDF - 79.50 € Tlačené - 79.50 €
Dostupnosť	SKLADOM
Cena	79.50 € bez DPH
79.50 €

Informácie o norme:

Označenie normy: ASTM D2440-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.2.2013
Kód tovaru: NS-20375
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Izolační oleje

Anotácia textu normy ASTM D2440-13 :

Keywords:

acid, aging, electrical oil, insulating mineral oil, oxidation, sludge, stability, transformer, ICS Number Code 29.040.10 (Insulating oils)

Doplňujúce informácie

Significance and Use

4.1 The oxidation stability test of mineral transformer oils is a method for assessing the amount of sludge and acid products formed in a transformer oil when the oil is tested under prescribed conditions. Good oxidation stability is necessary in order to maximize the service life of the oil by minimizing the formation of sludge and acid. Oils that meet the requirements specified for this test in Specification D3487 tend to minimize electrical conduction, ensure acceptable heat transfer, and preserve system life. There is no proven correlation between performance in this test and performance in service, since the test does not model the whole insulation system (oil, paper, enamel, wire). However, the test can be used as a control test for evaluating oxidation inhibitors and to check the consistency of oxidation stability of production oils.

1. Scope

1.1 This test method determines the resistance of mineral transformer oils to oxidation under prescribed accelerated aging conditions. Oxidation stability is measured by the propensity of oils to form sludge and acid products during oxidation. This test method is applicable to new oils, both uninhibited and inhibited, but is not well defined for used or reclaimed oils.

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D2112-15(2023)	Standard Test Method for Oxidation Stability of Inhibited Mineral Insulating Oil by Pressure Vessel
D974-22	Standard Test Method for Acid and Base Number by Color-Indicator Titration
D2272-22	Standard Test Method for Oxidation Stability of Steam Turbine Oils by Rotating Pressure Vessel
D3487-16e1	Standard Specification for Mineral Insulating Oil Used in Electrical Apparatus (Includes all amendments and changes 1/1/2018).
IEC 61125: 1992	Unused Hydrocarbon-Based Insulating Liquids--Test Methods for Evaluating the Oxidation Stability International Electrotechnical Commission. Available from American National Standards Institute, 25 W. 43rd St., 4th Floor, New York, NY 10036.
B1-13(2018)	Standard Specification for Hard-Drawn Copper Wire
D664-18e2	Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration (Includes all amendments and changes 1/4/2019).