Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D2419-22
Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate
NORMA vydaná dňa 15.9.2022
Informácie o norme:
Označenie normy: ASTM D2419-22
Dátum vydania normy: 15.9.2022
Kód tovaru: NS-1085289
Počet strán: 10
Približná hmotnosť: 30 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Zemní práce. Hloubicí práce. Budování základů. Podzemní práce
Anotácia textu normy ASTM D2419-22 :
Keywords:
ICS Number Code 93.020 (Earth works. Excavations. Foundation construction. Underground works)
Doplňujúce informácie
| Significance and Use | ||||||||||||||
|
5.1?This test method assigns an empirical value to the relative amount, fineness, and character of clay-like material present in the test specimen. 5.2?A minimum sand equivalent value may be specified to limit the permissible quantity of clay-like or clay-size fines in an aggregate. 5.3?This test method provides a rapid field method for determining changes in the quality of aggregates during production or placement. Note 3:?The quality of the results produced by this standard
are dependent upon the competence of the personnel performing the
procedure and the capability, calibration, and the maintenance of
the equipment used. Agencies that meet the criteria of
Specification D3666 are
generally considered capable of competent and objective testing,
sampling, inspection, etc. Users of this standard are cautioned
that compliance with Specification D3666 alone does not completely ensure
reliable results. Reliable results depend on many factors;
following the suggestions of Specification D3666 or similar acceptable guideline
provides a means of evaluating and controlling some of those
factors.
|
||||||||||||||
| 1. Scope | ||||||||||||||
|
1.1?This test method is intended to serve as a rapid field correlation test. The purpose of this test method is to indicate, under standard conditions, the relative proportions of clay-size or plastic fines and dust in granular soils and fine aggregates that pass the 4.75 mm (No. 4) sieve. The term sand equivalent expresses the concept that most granular soils and some fine aggregates are mixtures of desirable coarse particles, sand-size particles, and generally undesirable clay or plastic fines and dust. Note 1:?For fine aggregates containing clean dust of fracture
(clay-size particles that are not clay minerals), test results will
depend on the amount of fines present in the material. In this
case, other tests such as Methylene Blue Value (AASHTO T 330) or
X-ray diffraction (XRD) may be needed to determine if the fines are
deleterious.
Note 2:?Some agencies perform the test on material with a top
size smaller than the 4.75 mm (No. 4) sieve. This is done to avoid
trapping the clay-size or plastic fines and dust below flaky shaped
4.75 to 2.36 mm (No. 4 to 8) sized particles. Testing smaller top
sized material may lower the numerical results of the
test.
1.2?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.2.1?Regarding sieves, per Specification E11 subsection 1.3, the values stated in SI units shall be considered standard for the dimensions of the sieve cloth openings and the wire diameter used in the sieve cloth. The values stated in inch-pound units shall be considered standard with regard to the sieve frames, pans, and covers. When sieve mesh sizes are referenced, the alternate inch-pound designations are provided for information purposes and enclosed in parentheses. 1.3?The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||
| 2. Referenced Documents | ||||||||||||||
|
Doporučujeme:
