ASTM D5528-13
ASTM D5573-99(2012)..
ASTM D5766/D5766M-11..
ASTM D5961/D5961M-13..
ASTM D6115-97(2011)..
ASTM D6264/D6264M-12..
Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D2290-12
Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
Automaticky preložený názov:
Štandardná skúšobná metóda pre Zdanlivý Hoop pevnosti v ťahu plastickej alebo vystužené plastové rúrky
NORMA vydaná dňa 1.12.2012
Informácie o norme:
Označenie normy: ASTM D2290-12
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.12.2012
Kód tovaru: NS-19943
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D2290-12 :
Keywords:
apparent tensile strength, hoop tensile strength, plastic pipe, ring segment method, split-disk method, ICS Number Code 83.120 (Reinforced plastics)
Doplňujúce informácie
| Significance and Use | ||||||
|
4.1 Split disk and ring segment tensile tests, properly interpreted, provide reasonably accurate information with regard to the apparent tensile strength of plastic pipe when employed under conditions approximating those under which the tests are made. 4.2 Ring tensile tests may provide data for research and development, engineering design, quality control, acceptance or rejection under specifications, and for special purposes. The test cannot be considered significant for applications differing widely from the load-time scale of the standard test. 1.1 This test method covers the
determination of the comparative apparent tensile strength of most
plastic products utilizing a split disk or ring segment test
fixture, when tested under defined conditions of pretreatment,
temperature, humidity, and test machine speed. This test method is
applicable to reinforced-thermosetting resin pipe regardless of
fabrication method. This test method also is applicable to extruded
and molded thermoplastic pipe.
Procedure A is used for reinforced-thermosetting resin pipe; Procedure B is used for thermoplastic pipe of any size; Procedure C is used for thermoplastic pipe with nominal diameter of 41/2 in. (110 mm) and greater. Procedure D is used for polyethylene pipe with a nominal diameter of 14 in. (350 mm) and greater and preferably having wall thickness 1 in. (25 mm) and greater. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||
| 2. Referenced Documents | ||||||
|
Podobné normy:
Historická
1.10.2013
Historická
1.10.2012
Historická
1.1.2011
Historická
1.5.2013
Historická
1.8.2011
Historická
1.4.2012
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
