Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D2239-22

Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

NORMA vydaná dňa 1.11.2022

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 58.40 € PDF + redline - ihneď - 70.10 € Tlačené - 58.40 € Tlač + redline - 70.10 €
Dostupnosť	SKLADOM
Cena	58.40 € bez DPH
58.40 €

Informácie o norme:

Označenie normy: ASTM D2239-22
Dátum vydania normy: 1.11.2022
Kód tovaru: NS-1090588
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Trubky z plastické hmoty

Anotácia textu normy ASTM D2239-22 :

This specification covers polyethylene (PE) pipe made in standard thermoplastic pipe dimension ratios and pressure rated for water. Polyethylene plastics used to make pipe meeting the requirements of this specification are categorized in two criteria: short-term strength tests and long-term strength tests. The plastics are defined by four hydrostatic design stresses developed on the basis of long-term tests. The material shall conform to the required limits of burst pressure, environmental stress cracking, and sustained pressure.

Keywords:
ID controlled pipe, IDR, inside diameter controlled pipe, PE pipe, plastic pipe, polyethylene pipe, potable water pipe, service pipe, SIDR, water pipe, water service pipe,, ICS Number Code 23.040.20 (Plastic pipes)

Doplňujúce informácie

1. Scope

1.1?This specification covers polyethylene (PE) pipe made to standard inside dimension ratios (SIDR) and pressure rated for water (see appendix). Included are requirements for PE compounds and requirements and test methods for workmanship, dimensions, elevated temperature sustained pressure, burst pressure, and marking.

Note 1:?Refer to specification AWWA C901and PPI Technical Note 49 (TN-49) for further information on pipe suitability for potable water end use applications. Oxidative Resistance Classification (CC# rating) information is available from NSF International.

1.2?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3?The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes shall not be considered as requirements of the specification. Notes and footnotes in tables and figures, and Supplementary Requirements are requirements of the specification.

1.4?The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

D2565-23	Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications
APWA	Uniform Color Code
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D1599-18	Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1598-23	Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D1238-23a	Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer (Includes all amendments and changes 12/6/2023).
D618-21	Standard Practice for Conditioning Plastics for Testing
NSF/ANSI Standard No. 61	for Drinking Water Systems Components--Health Effects
PPI TR-4	HDB/SDB/PDB/MRS Listed Materials, PPI Listing of Hydrostatic Design Basis (HDB), Strength Design Basis (SDB), Pressure Design Basis (PDB), and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials or Pipe
D1603-20	Standard Test Method for Carbon Black Content in Olefin Plastics
D638-22	Standard Test Method for Tensile Properties of Plastics
F412-23	Standard Terminology Relating to Plastic Piping Systems
D4218-20	Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique
D3350-21	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
D2837-22	Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
G154-23	Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Materials
G155-21	Standard Practice for Operating Xenon Arc Lamp Apparatus for Exposure of Materials
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

Odporúčame:

Aktualizácia zákonov

Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.