Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D2103-10

Standard Specification for Polyethylene Film and Sheeting

Automaticky preložený názov:

Štandard Specification pre PET film a paženie

NORMA vydaná dňa 1.4.2010

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 72.80 € Tlačené - 72.80 €
Dostupnosť	SKLADOM
Cena	72.80 € bez DPH
72.80 €

Informácie o norme:

Označenie normy: ASTM D2103-10
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.4.2010
Kód tovaru: NS-19299
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM D2103-10 :

Keywords:

ethylene plastics, polyethylene film, polyethylene plastics, polyethylene sheeting, recycling, Polyethylene (PE) sheet and film--specifications, Plastic sheet and film--specifications, Thickness--plastics, Transmittance and reflectance--plastics, Yield--plastic sheet and film, Plastics--specifications, ICS Number Code 83.140.10 (Films and sheets)

Doplňujúce informácie

1. Scope

1.1 This specification covers the classification of polyethylene film and sheeting up to 0.3 mm (0.012 in.) in thickness, inclusive. The film or sheeting may contain additives for the improvement of the surface properties, pigments, or stabilizers, or combinations thereof.

1.2 The values stated in SI units are to be regarded as standard. The values given in brackets are for information only.

1.3 The following precautionary caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.4 This specification allows for the use of recycled polyethylene film or resin as feedstock, in whole or in part, as long as all the requirements as governed by the producer and end user are also met (see Note 1).

Note 1—Guide D7209 describes terminology and definitions related to recycled plastics.

Note 2—There is no known ISO equivalent to this specification.

2. Referenced Documents

D1709-22	Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
D1746-23	Standard Test Method for Transparency of Plastic Sheeting
D1894-14	Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting (Withdrawn 2023)
D1922-23	Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
D1938-19	Standard Test Method for Tear-Propagation Resistance (Trouser Tear) of Plastic Film and Thin Sheeting by a Single-Tear Method
D1434-23	Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
D3892-15(2020)	Standard Practice for Packaging/Packing of Plastics
D2578-23	Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
D2839-16(2023)	Standard Practice for Use of a Melt Index Strand for Determining Density of Polyethylene
D618-21	Standard Practice for Conditioning Plastics for Testing
D792-20	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D882-18	Standard Test Method for Tensile Properties of Thin Plastic Sheeting
D883-24	Standard Terminology Relating to Plastics
D1003-21	Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
D1004-21	Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting
E96/E96M-23	Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
F1249-20	Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor
D5947-18	Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
D6988-21	Standard Guide for Determination of Thickness of Plastic Film Test Specimens
D7209-06	Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015)
D2457-21	Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
D4321-15	Standard Test Method for Package Yield of Plastic Film (Withdrawn 2024)
D4703-16	Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
D4976-12a(2020)	Standard Specification for Polyethylene Plastics Molding and Extrusion Materials (Includes all amendments and changes 11/17/2022).
D1505-18	Standard Test Method for Density of Plastics by the Density-Gradient Technique

Odporúčame:

Aktualizácia zákonov

Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.