Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D198-21a
Standard Test Methods of Static Tests of Lumber in Structural Sizes (Includes all amendments And changes 8/16/2022).
NORMA vydaná dňa 1.8.2021
Informácie o norme:
Označenie normy: ASTM D198-21a
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.8.2021
Kód tovaru: NS-1033642
Počet strán: 29
Približná hmotnosť: 87 g (0.19 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM D198-21a :
Keywords:
apparent modulus of elasticity, compression, flexure, modulus of elasticity, modulus of rupture, shear, shear modulus, shear-free modulus of elasticity, structural members, tension, torsion, torsional shear modulus, wood, wood-based materials,, ICS Number Code 79.040 (Wood, sawlogs and sawn timber)
Doplňujúce informácie
| Significance and Use | ||||||||||||||||||||||||||||
|
6.1?The flexural properties established by this test method provide: 6.1.1?Data for use in development of grading rules and specifications; 6.1.2?Data for use in development of design values for structural members; 6.1.3?Data on the influence of imperfections on mechanical properties of structural members; 6.1.4?Data on strength properties of different species or grades in various structural sizes; 6.1.5?Data for use in checking existing equations or hypotheses relating to the structural behavior; 6.1.6?Data on the effects of chemical or environmental conditions on mechanical properties; 6.1.7?Data on effects of fabrication variables such as depth, taper, notches, or type of end joint in laminations; and 6.1.8?Data on relationships between mechanical and physical properties. 6.2?Procedures are described here in sufficient detail to permit duplication in different laboratories so that comparisons of results from different sources will be valid. Where special circumstances require deviation from some details of these procedures, these deviations shall be carefully described in the report (see Section 11). |
||||||||||||||||||||||||||||
| 1. Scope | ||||||||||||||||||||||||||||
|
1.1?These test methods cover the evaluation of lumber and wood-based products in structural sizes by various testing procedures. 1.2?The test methods appear in the following order:
1.3?Notations and symbols relating to the various testing procedures are given in Appendix X1. 1.4?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
