Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D1710-99

Standard Specification for Extruded and Compression Molded Polytetrafluoroethylene (PTFE) Rod and Heavy-Walled Tubing

Automaticky preložený názov:

Štandardné špecifikácie pre extrudované a lisované polytetrafluóretylénu ( PTFE ) Rod a Heavy - Walled Hadica

NORMA vydaná dňa 10.3.2002

Jazyk
Prevedenie	Online zabezpečené PDF - 75.60 € Tlačené - 75.60 €
Dostupnosť	SKLADOM
Cena	75.60 € bez DPH
75.60 €

Informácie o norme:

Označenie normy: ASTM D1710-99
Poznámka: NEPLATNÁ
Dátum vydania normy: 10.3.2002
Kód tovaru: NS-18142
Počet strán: 6
Približná hmotnosť: 18 g (0.04 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM D1710-99 :

Keywords:

fluorocarbon polymer, fluoropolymers, granular PTFE, polytetrafluoroethylene, PTFE, PTFE heavy-walled tubing, PTFE rod, ICS Number Code 83.140.99 (Other rubber and plastic products)

Doplňujúce informácie

1. Scope

1.1 This specification covers polytetrafluoroethylene (PTFE) rod and heavy-walled tubing manufactured from the PTFE resin of Specification D 4894 and reprocessed PTFE resin (as defined in Guide D 5033).

1.2 The specification covers rod 200-mm (8-in.) nominal diameter or under and heavy-walled tubing 100-mm outside diameter and with a wall thickness of 1.6 mm (1/16 in.) or greater. These materials must be made wholly from PTFE and produced in accordance with good commercial practice.

Note 1—Although this specification and ISO/DIS 13000-1 (1997) and ISO/DIS 13000-2 (1997) differ in approach or detail, data obtained using either are technically equivalent.

1.3 The values stated in SI units, as detailed in IEEE/ASTM SI 10 are to be regarded as the standard. The inch-pound units given in parentheses are provided for information only.

1.4 The following precautionary caveat pertains to the test methods portion, Section 12, only of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D149-25	Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
IEEE/ASTM SI 10	Standard for the Use of the International System of Units (SI): The Modern Metric System Available from ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428.
D5947-24	Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
D4894-19(2024)	Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials
D3892-15(2020)	Standard Practice for Packaging/Packing of Plastics
D792-20	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D618-21	Standard Practice for Conditioning Plastics for Testing
D374-99	Standard Test Methods for Thickness of Solid Electrical Insulation
D5740-18(2025)	Standard Guide for Writing Material Standards in the Classification D4000 Format
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D883-26a	Standard Terminology Relating to Plastics (Includes all amendments and changes 6/15/2026).
E94-04	Standard Guide for Radiographic Examination
ISO 13000-2 (2005)	PlasticsPolytetrafluoroethylene (PTFE) Semi-Finished Products, Part 2: Preparation of Test Specimen and Determination of Properties
ISO 13000-1 (2005)	PlasticsPolytetrafluoroethylene (PTFE) Semi-Finished Products, Part 1: Basis for Specification
D7209-06	Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015)

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.