Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
Automaticky preložený názov:
Štandardná skúšobná metóda pre mechanické vlastnosti plastov použitím Microtensile vzoriek
NORMA vydaná dňa 1.9.2013
Označenie normy: ASTM D1708-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.9.2013
Kód tovaru: NS-18130
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
microtensile, plastics test method, tensile properties, ICS Number Code 83.080.01 (Plastics in general)
Significance and Use | ||||||||||||||||
4.1 This test method provides data for quality control and acceptance or rejection under specifications. 4.2 Before proceeding with this test method, reference should be made to the ASTM specification of the material being tested. Any test specimen preparation, conditioning, dimensions, or testing parameters, or combination thereof, covered in the materials specification shall take precedence over those mentioned in this test method. If there are no material specifications, then the default conditions herein apply. 1.1 This test method covers certain material specifications for which a history of data has been obtained using the standard microtensile specimen. In general, this test method is superseded for general use by either Test Methods D882 or Test Method D638. The very small Type V specimen in Test Method D638 is the recommended specimen when limited amounts of material are available. 1.2 This test method covers the determination of the comparative tensile strength and elongation properties of plastics in the form of standard microtensile test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed. This method is applicable when using specimens of any thickness up to 3.2 mm (1/8 in.), including thin films. 1.3 This test method cannot be used for the determination of modulus of elasticity. For the determination of modulus, see Test Method D638 or Test Methods D882. 1.4 Test data obtained by this test method are relevant and appropriate for use in engineering design. 1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
|
Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
|
|
Standard Guide for Determination of Thickness of Plastic Film Test Specimens
|
|
Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
|
|
Standard Classification System for Specifying Plastic Materials
|
|
Standard Terminology Relating to Plastics
|
|
Standard Test Method for Tensile Properties of Thin Plastic Sheeting
|
|
Standard Test Method for Tensile Properties of Plastics
|
|
Standard Practice for Conditioning Plastics for Testing |
Historická
1.4.2011
Historická
1.11.2013
Historická
1.4.2010
Historická
15.3.2011
Historická
1.6.2013
Historická
1.4.2010
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-11-04 (Počet položiek: 2 209 323)
© Copyright 2024 NORMSERVIS s.r.o.