Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM D1415-18

Standard Test Method for Rubber Property´International Hardness

NORMA vydaná dňa 1.6.2018

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 58.90 € PDF + redline - ihneď - 70.70 € Tlačené - 58.90 € Tlač + redline - 70.70 €
Dostupnosť	SKLADOM
Cena	58.90 € bez DPH
58.90 €

Informácie o norme:

Označenie normy: ASTM D1415-18
Dátum vydania normy: 1.6.2018
Kód tovaru: NS-897712
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Pryž

Anotácia textu normy ASTM D1415-18 :

Keywords:
ICS Number Code 83.060 (Rubber)

Doplňujúce informácie

Significance and Use

4.1 The International Hardness test is based on measurement of the penetration of a rigid ball into the rubber specimen under specified conditions. The measured penetration is converted into IRHD, the scale of degrees being so chosen that 0 represents a material having an elastic modulus of zero, and 100 represents a material of infinite elastic modulus.

4.1.1 The scale also fulfills the following conditions over most of the normal range of hardness: one IRHD range represents approximately the same proportionate difference in Young's modulus, and for rubber vulcanizates in the usual range of resilience, readings in IRHD are comparable with those given by a Type A durometer (Test Method D2240) when testing standard specimens.

4.1.1.1 The term “usual range of resilience” is used to exclude those compounds that have unusually high rates of stress relaxation or deformational hysteresis. For such compounds, differences in the dwell time in the two hardness tests (Test Methods D2240 and D1415) result in differences in hardness values. Readings may not be comparable when testing curved or irregularly shaped test specimens.

4.1.2 For substantially elastic isotropic materials like well-vulcanized natural rubbers, the hardness in IRHD bears a known relation to Young's modulus, although for markedly plastic or anisotropic rubbers the relationship will be less precisely known.

4.1.3 The relation between the difference of penetration and the hardness expressed in IRHD is based on the following:

4.1.3.1 The relation4 between penetration and Young's modulus for a perfectly elastic isotropic material:

4.1.3.2 Use of a probit (integrated normal error) curve to relate log₁₀ M and hardness in IRHD, as shown in Fig. 1. This curve is defined as follows:

FIG. 1 Point Curve to Relate Log₁₀ M and the Hardness in IRHD

4.1.3.3 The value of log₁₀ M corresponding to the midpoint of the curve is equal to 0.364, that is, M = 2.31 MPa or 335 psi.

4.1.3.4 The maximum slope is equal to 57 IRHD per unit increase in log₁₀ M.

1. Scope

1.1 This test method covers a procedure for measuring the hardness of vulcanized or thermoplastic rubber. The hardness is obtained by the difference in penetration depth of a specified dimension ball under two conditions of contact with the rubber: (1.2 This test method is technically similar to ISO 48.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

D2240-15(2021)	Standard Test Method for Rubber Property—Durometer Hardness
D1349-14(2019)	Standard Practice for Rubber´Standard Conditions for Testing
ISO 48	Rubber, Vulcanized or Thermoplastic--Determination of Hardness (Hardness between 10 and 100 IRHD)
D4483-20	Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries

Odporúčame:

EviZak - všetky zákony vrátane ich evidencie na jednom mieste

Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !

Chcete vedieť viac informácii ? Pozrite sa na túto stránku.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.

Súhlas môžete odmietnuť tu.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.