Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM D1404/D1404M-99(2008)
Standard Test Method for Estimation of Deleterious Particles in Lubricating Grease
Automaticky preložený názov:
Štandardná skúšobná metóda pre odhad škodlivých častíc v mazacím tukom
NORMA vydaná dňa 1.5.2008
Informácie o norme:
Označenie normy: ASTM D1404/D1404M-99(2008)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.5.2008
Kód tovaru: NS-17182
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Anotácia textu normy ASTM D1404/D1404M-99(2008) :
Keywords:
abrasive particles, cleanliness, contamination, deleterious particles, lubricating grease, particles, scratch test, Abrasive particles, Cleanliness, Contamination--petroleum products, Deleterious particles, Lubricating grease, Particle analysis--petroleum products, Scratch testing, ICS Number Code 75.100 (Lubricants, industrial oils and related products)
Doplňujúce informácie
| Significance and Use | ||||||
| p>The significance of the number of scratches as far as
correlation with field performance is concerned has not been
established. A particle which is abrasive to plastic will not
necessarily be abrasive to steel or other bearing materials. Some
correlation was obtained in that the contaminant used in Sample 3
(see 10.1.1) had a greater wear rate in a laboratory ball bearing
abrasive wear test than the contaminant in Sample 2.
Note 1—The number of scratches obtained cannot be used to draw fine differences between greases, but rather, to group them into two or three general classes. One such possible division could be:
An advantage of this test method is that each test takes only a few minutes to run. This test method is used for quality control and specification purpose. |
||||||
| 1. Scope | ||||||
|
1.1 This test method covers a procedure for the detection and estimation of deleterious particles in lubricating grease. 1.2 This test method is applicable to all lubricating greases. It can also be used to test other semi-solid or viscous materials. Grease fillers, such as graphite and molybdenum disulfide, can be tested for abrasive contaminants by first mixing them into petrolatum or grease known to be free of deleterious particles. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Within the text, the SI units are shown in brackets. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||
| 2. Referenced Documents | ||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
