Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Test Method for Stiffness Properties of Plastics as a Function of Temperature by Means of a Torsion Test
Automaticky preložený názov:
Štandardná skúšobná metóda pre tuhosti vlastnosti plastov ako funkcia teploty pomocou torznej testu
NORMA vydaná dňa 1.4.2010
Označenie normy: ASTM D1043-10
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.4.2010
Kód tovaru: NS-16134
Počet strán: 11
Približná hmotnosť: 33 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
Clash-Berg, modulus of rigidity, plastics, shear, torsion, Modulus of rigidity, Rigid plastics, Stiffness--plastics, Torsion testing--plastics, ICS Number Code 83.080.01 (Plast in general)
Significance and Use | ||||||||||||||||||||
The property measured by this test is the apparent modulus of rigidity, G, sometimes called the apparent shear modulus of elasticity. It is important to note that this property is not the same as the modulus of elasticity, E, measured in tension, flexure, or compression. The relationship between these properties is shown in Annex A1. The measured modulus of rigidity is termed “apparent” since it is the value obtained by measuring the angular deflection occurring when the specimen is subjected to an applied torque. Since it is possible that the specimen will be deflected beyond its elastic limit, the calculated value will not always represent the true modulus of rigidity within the elastic limit of the material. In addition, the value obtained by this test method will also be affected by the creep characteristics of the material, since the load application time is arbitrarily fixed. For many materials, it is possible that there is a specification that requires the use of this test method, but with some procedural modifications that take precedence when adhering to the specification. Therefore, it is advisable to refer to that material specification before using this test method. Table 1 in Classification D4000 lists the current ASTM material standards. This test method is useful for determining the relative changes in stiffness over a wide range of temperatures. |
||||||||||||||||||||
1. Scope | ||||||||||||||||||||
1.1 This test method covers the determination of the stiffness characteristics of plastics over a wide temperature range by direct measurement of the apparent modulus of rigidity. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1—This test method and ISO 458-1 and ISO 458-2 address the same subject matter, but differ in technical content. |
||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||
|
Historická
1.8.2010
Historická
1.4.2010
Historická
1.9.2009
Historická
1.11.2013
Historická
1.7.2010
Historická
1.3.2007
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-12-22 (Počet položiek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.