Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM C612-14

Standard Specification for Mineral Fiber Block and Board Thermal Insulation

Automaticky preložený názov:

Štandardné špecifikácie pre minerálne vlákna Block a rady tepelnou izoláciou

NORMA vydaná dňa 1.1.2014

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 70.80 € Tlačené - 70.80 €
Dostupnosť	SKLADOM
Cena	70.80 € bez DPH
70.80 €

Informácie o norme:

Označenie normy: ASTM C612-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.1.2014
Kód tovaru: NS-14255
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Tepelně a zvukově izolační materiály

Anotácia textu normy ASTM C612-14 :

Keywords:

block, board, high temperature, mineral fiber insulation, rock fiber, shot, shot content, slag fiber, ICS Number Code 91.100.60 (Thermal and sound insulating materials)

Doplňujúce informácie

1. Scope

1.1 This specification covers the classification, composition, dimension, and physical properties of mineral fiber (rock, slag, or glass) semi-rigid and rigid board intended for the use as thermal insulation on surfaces operating at temperatures between 0°F (-18°C) and 1800°F (982°C). For specific applications, the actual temperature limits shall be agreed upon between the supplier and the purchaser.

1.2 For satisfactory performance, properly installed protective vapor retarder or barriers shall be used on below ambient temperature applications to reduce movement of water through or around the insulation towards the colder surface. Failure to use a vapor retarder or barrier can lead to insulation and system damage. Refer to Practice C921 to aid material selection. Although vapor retarder properties are not part of this specification, properties required in Specification C1136 are pertinent to applications or performance.

1.3 The orientation of the fibers within the boards is primarily parallel to the principal surface (face). This specification does not cover fabricated pipe and tank wrap insulation where the insulation has been cut and fabricated to provide a fiber orientation that is perpendicular to the surface (face).

1.4 This standard does not purport to provide the performance requirements of hourly-rated fire systems. Consult the manufacturer for the appropriate system.

1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

C447-15(2022)	Standard Practice for Estimating the Maximum Use Temperature of Thermal Insulations
C165-23	Standard Test Method for Measuring Compressive Properties of Thermal Insulations
C795-08(2023)	Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel
C921-10	Standard Practice for Determining the Properties of Jacketing Materials for Thermal Insulation
C1045-19	Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
C1136-23	Standard Specification for Flexible, Low Permeance Vapor Retarders for Thermal Insulation
E84-23d	Standard Test Method for Surface Burning Characteristics of Building Materials (Includes all amendments and changes 1/29/2024).
CAN/ULC-S102	Standard Method of Test for Surface Burning Characteristics of Building Materials and Assemblies Available from Underwriters Laboratories of Canada, 7 Crouse Road, Scarborough, Ontario, Canada M1R 3A9.
C168-22	Standard Terminology Relating to Thermal Insulation
C303-21	Standard Test Method for Dimensions and Density of Preformed Block and Board–Type Thermal Insulation
C356-22	Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat
C390-08(2019)	Standard Practice for Sampling and Acceptance of Thermal Insulation Lots
C1101/C1101M-23	Standard Test Methods for Classifying the Flexibility or Rigidity of Mineral Fiber Blanket and Board Insulation
C177-19e1	Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus (Includes all amendments and changes 2/23/2023).
C411-19	Standard Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
C665-23	Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing
C680-23a	Standard Practice for Estimate of the Heat Gain or Loss and the Surface Temperatures of Insulated Flat, Cylindrical, and Spherical Systems by Use of Computer Programs (Includes all amendments and changes 12/13/2023).
C1058-03	Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
C1335-23	Standard Test Method for Measuring Non-Fibrous Content of Man-Made Rock and Slag Mineral Fiber Insulation
C1338-19(2022)	Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings
C1617-19	Standard Practice for Quantitative Accelerated Laboratory Evaluation of Extraction Solutions Containing Ions Leached from Thermal Insulation on Aqueous Corrosion of Metals
C1104/C1104M-19	Standard Test Method for Determining the Water Vapor Sorption of Unfaced Mineral Fiber Insulation
C1114-06(2019)	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
C1304-23	Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials
C518-21	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus

Podobné normy:

ASTM C1676-08

Historická
15.4.2008

ASTM C168-13

Historická
1.4.2013

ASTM C1728-13

Historická
1.5.2013

ASTM C1729-14a

Historická
1.9.2014

ASTM C1729M-14a

Historická
1.9.2014

ASTM C1763-14

Historická
1.5.2014

Odporúčame:

EviZak - všetky zákony vrátane ich evidencie na jednom mieste

Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !

Chcete vedieť viac informácii ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.