Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM C582-95

Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment

Automaticky preložený názov:

Štandardné špecifikácie pre Bezkontaktné Čelné vystužený reaktoplastových ( RTP ) , lamináty pre odolné proti korózii zariadení

NORMA vydaná dňa 1.1.1995

Jazyk
Prevedenie	Online zabezpečené PDF - 75.40 € Tlačené - 75.40 €
Dostupnosť	SKLADOM
Cena	75.40 € bez DPH
75.40 €

Informácie o norme:

Označenie normy: ASTM C582-95
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.1.1995
Kód tovaru: NS-14115
Počet strán: 7
Približná hmotnosť: 21 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM C582-95 :

Keywords:

corrosive service applications-plast, contact-molded reinforced thermosetting plastic (RTP) laminates for, corrosion resistant equipment, spec., , Plast (reinforced thermosetting)-structural, contact-molded reinforced thermosetting plastic (RTP) laminates for, corrosion resistant equipment, ICS Number Code 83.140.20 (Laminated sheets)

Doplňujúce informácie

1. Scope

1.1 This specification covers composition, thickness, fabricating procedures, and physical property requirements for glass fiber reinforced thermoset polyester, vinyl ester, or other qualified thermosetting resin laminates comprising the materials of construction for RTP corrosion-resistant tanks, piping, and equipment. This specification is limited to fabrication by contact molding.

Note 1-The laminates covered by this specification are manufactured during fabrication of contact-molded RTP tanks, piping, and other equipment. Note 2-There is no similar or equivalent ISO standard.

1.2 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

D2584-25	Standard Test Method for Ignition Loss of Cured Reinforced Resins
D2583-25	Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
D883-26a	Standard Terminology Relating to Plastics (Includes all amendments and changes 6/15/2026).
D790-25	Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D695-26	Standard Test Method for Compressive Properties of Rigid Plastics
D638-22	Standard Test Method for Tensile Properties of Plastics
C581-26	Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service
D3681-23	Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition
E84-26a	Standard Test Method for Surface Burning Characteristics of Building Materials (Includes all amendments and changes 4/15/2026).

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.