Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM C578-22

Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation

NORMA vydaná dňa 1.8.2022

Jazyk
Prevedenie	Online zabezpečené PDF - 75.40 € Tlačené - 75.40 €
Dostupnosť	SKLADOM
Cena	75.40 € bez DPH
75.40 €

Informácie o norme:

Označenie normy: ASTM C578-22
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.8.2022
Kód tovaru: NS-1070821
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Lehčené plastické hmoty
Tepelně a zvukově izolační materiály

Anotácia textu normy ASTM C578-22 :

Keywords:

block/board, cellular polystyrene, foam plastic, polystyrene, RCPS, rigid cellular polystyrene, thermal insulation,, ICS Number Code 83.100 (Cellular materials),91.100.60 (Thermal and sound insulating materials)

Doplňujúce informácie

1. Scope

1.1?This specification1.1.1?Additional requirements for Types IV and XIII for pipe, tank, and equipment thermal insulation for temperatures from 320 to +165?F (196 to +73.9?C) are contained in Annex A1.

1.2?The use of thermal insulation materials covered by this specification is potentially regulated by codes that address fire performance. For some end uses, specifiers need to also address the effect of moisture and wind pressure resistance. Guidelines regarding these end use considerations are included in Appendix X1.

1.3?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

E176-24a	Standard Terminology of Fire Standards (Includes all amendments and changes 12/9/2024).
D1621-16(2023)	Standard Test Method for Compressive Properties of Rigid Cellular Plastics
D1622-20	Standard Test Method for Apparent Density of Rigid Cellular Plastics
D2126-25	Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging
D2863-23e1	Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) (Includes all amendments and changes 8/18/2025).
C165-23	Standard Test Method for Measuring Compressive Properties of Thermal Insulations
C168-25	Standard Terminology Relating to Thermal Insulation
C177-19e1	Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus (Includes all amendments and changes 2/23/2023).
C203-22	Standard Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation
C272-01	Standard Test Method for Water Absorption of Core Materials for Structural Sandwich Constructions
C303-21	Standard Test Method for Dimensions and Density of Preformed Block and Board–Type Thermal Insulation
C1512-10(2020)	Standard Test Method for Characterizing the Effect of Exposure to Environmental Cycling on Thermal Performance of Insulation Products
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
E96/E96M-24a	Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials (Includes all amendments and changes 11/20/2024).
E84-26a	Standard Test Method for Surface Burning Characteristics of Building Materials (Includes all amendments and changes 4/15/2026).
C1303-09	Standard Test Method for Predicting Long-Term Thermal Resistance of Closed-Cell Foam Insulation
C1363-24	Standard Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus
C335-05a	Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation
C390-08(2024)	Standard Practice for Sampling and Acceptance of Thermal Insulation Lots
C518-21	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
C550-26	Standard Test Method for Measuring Trueness and Squareness of Rigid Block and Board Thermal Insulation
C870-24	Standard Practice for Conditioning of Thermal Insulating Materials
C1045-19	Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
C1058-03	Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
C1114-06(2019)	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
CAN/ULC S770	Standard Test Method for the Determination of Long-Term Thermal Resistance of Closed-Cell Thermal Insulating Foams

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.