ASTM C842-05(2010)e1..
ASTM C843-99(2012)..
ASTM C844-04(2010)..
ASTM C845/C845M-12..
ASTM C87/C87M-10..
ASTM C887-13
Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM C531-00(2012)
Standard Test Method for Linear Shrinkage and Coefficient of Thermal Expansion of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes
Automaticky preložený názov:
Štandardná skúšobná metóda pre Lineárny zmrštenie a koeficient teplotnej rozťažnosti chemicky odolné malty, zálievky, monolitické Surfacings a polymérbetóny
NORMA vydaná dňa 1.8.2012
Informácie o norme:
Označenie normy: ASTM C531-00(2012)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.8.2012
Kód tovaru: NS-13882
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM C531-00(2012) :
Keywords:
brick mortars, grouts, linear shrinkage, monolithic surfacings, mortars, polymer concretes, thermal expansion, tile grouts, ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)
Doplňujúce informácie
| Significance and Use | ||||||
|
4.1 This test method offers a means of comparing the relative linear shrinkage and coefficient of thermal expansion. 4.1.1 The material to be tested is placed in the mold in a fluid or plastic state. As the material makes a transition to a solid state, it adheres to and captures the end studs. 4.1.2 The linear shrinkage measured is the change in length that occurs after the material is rigid enough and strong enough to move the studs. 4.2 This test method can be used for research purposes to provide information on linear changes taking place in the test materials. Other dimensional changes may occur that do not manifest themselves as changes in length. |
||||||
| 1. Scope | ||||||
|
1.1 This test method covers the measurement of the linear shrinkage during setting and curing and the coefficient of thermal expansion of chemical-resistant mortars, grouts, monolithic surfacings, and polymer concretes. 1.2 A bar of square cross-section is cast to a prescribed length in a mold that holds measuring studs that are captured in the ends of the finished casting. 1.2.1 The change in length after curing is measured and used to calculate shrinkage. 1.2.2 The change in length at a
specific elevated temperature is measured and used to calculate the
coefficient of thermal expansion.
1.3 This test method is limited to materials with aggregate size of 0.25 in. (6 mm) or less. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||
| 2. Referenced Documents | ||||||
|
Podobné normy:
Historická
1.10.2010
Historická
1.3.2012
Historická
15.5.2010
Historická
15.12.2012
Historická
15.12.2010
Historická
1.8.2013
Odporúčame:
Aktualizácia zákonov
Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
