Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM C449-07(2013)

Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement

Automaticky preložený názov:

Štandardné špecifikácie pre minerálne vlákna Hydraulické nastavenie tepelnoizolačné a dokončovacie Cement

NORMA vydaná dňa 1.3.2013

Jazyk
Prevedenie	Online zabezpečené PDF - 63.20 € Tlačené - 63.20 €
Dostupnosť	SKLADOM
Cena	63.20 € bez DPH
63.20 €

Informácie o norme:

Označenie normy: ASTM C449-07(2013)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2013
Kód tovaru: NS-13444
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Cement. Sádra. Vápno. Malta

Anotácia textu normy ASTM C449-07(2013) :

Keywords:

cement, finishing, hydraulic-setting, insulating, mineral fiber, thermal, thermal conductivity, ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)

Doplňujúce informácie

1. Scope

1.1 This specification covers mineral fiber (rock or slag) insulating and finishing cement shipped in dry-mix form, including hydraulic-setting binder, which, when mixed with water and applied in accordance with the manufacturer's directions, affords a smooth surface as a final finish for heated surfaces up to 1200 °F (649 °C) for specific applications. The actual temperature limit shall be agreed upon between the purchaser and the manufacturer.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 The following safety hazards caveat pertains only to the test method (Section 10) described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.4 When the installation or use of thermal insulation materials, accessories, and systems pose safety or health problems, the manufacturer shall provide the user with appropriate current information regarding any known problems associated with the recommended use of the company's products and shall also recommend protective measures to be employed in their safe utilization. The user shall establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

2. Referenced Documents

C1114-06(2019)	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
E136-24	Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750 ?C
C166-05(2023)	Standard Test Method for Covering Capacity and Volume Change Upon Drying of Thermal Insulating Cement
C163-05(2023)	Standard Practice for Mixing Thermal Insulating Cement Samples
C1058-03	Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
C177-19e1	Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus (Includes all amendments and changes 2/23/2023).
C390-08(2019)	Standard Practice for Sampling and Acceptance of Thermal Insulation Lots
C411-19	Standard Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
C518-21	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
C795-08(2023)	Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel
C1045-19	Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
C356-22	Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat
C168-22	Standard Terminology Relating to Thermal Insulation

Podobné normy:

ASTM C452/C452M-10..

Historická
1.6.2010

ASTM C465-10

Historická
1.2.2010

ASTM C466-03(2012)..

Historická
1.8.2012

ASTM C471M-13

Historická
1.12.2013

ASTM C472-99(2014)..

Historická
1.4.2014

ASTM C473-12

Historická
1.9.2012

Odporúčame:

Aktualizácia zákonov

Chcete mať istotu o platnosti využívaných predpisov?
Ponúkame Vám riešenie, aby ste mohli používať stále platné (aktuálne) legislatívne predpisy
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.