Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

NEPLATNÁ ASTM C195-07(2013) 1.3.2013 náhľad

Doplňujúce informácie

ASTM C195-07(2013)

Standard Specification for Mineral Fiber Thermal Insulating Cement

Automaticky preložený názov:

Štandardné špecifikácie pre minerálne vlákna tepelnoizolačné Cement

NORMA vydaná dňa 1.3.2013

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 70.10 € Tlačené - 70.10 €
Dostupnosť	SKLADOM
Cena	70.10 € bez DPH
70.10 €

Informácie o norme:

Označenie normy: ASTM C195-07(2013)
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.3.2013
Kód tovaru: NS-12490
Počet strán: 3
Približná hmotnosť: 9 g (0.02 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Cement. Sádra. Vápno. Malta

Anotácia textu normy ASTM C195-07(2013) :

Keywords:

insulating cement, mineral fiber, thermal insulation, ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)

Doplňujúce informácie

1. Scope

1.1 This specification covers mineral fiber thermal insulating materials in the form of dry cement, which, when mixed with a suitable proportion of water, applied as a plastic mass, and dried in place, affords resistance to heat transmission on surfaces operating at temperatures between 250 and 1900°F (about 121 and 1038°C).

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 The following safety hazards caveat pertains only to the test methods section of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

C163-05(2023)	Standard Practice for Mixing Thermal Insulating Cement Samples
C166-05(2023)	Standard Test Method for Covering Capacity and Volume Change Upon Drying of Thermal Insulating Cement
C1114-06(2019)	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
C390-08(2019)	Standard Practice for Sampling and Acceptance of Thermal Insulation Lots
C411-19	Standard Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
C518-21	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
C1045-19	Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
C1058-03	Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
E136-24	Standard Test Method for Assessing Combustibility of Materials Using a Vertical Tube Furnace at 750 ?C
C136-06	Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
C356-22	Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat
C177-19e1	Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus (Includes all amendments and changes 2/23/2023).
C168-22	Standard Terminology Relating to Thermal Insulation