Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM C150/C150M-22
Standard Specification for Portland Cement
NORMA vydaná dňa 1.7.2022
Informácie o norme:
Označenie normy: ASTM C150/C150M-22
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.7.2022
Kód tovaru: NS-1068713
Počet strán: 9
Približná hmotnosť: 27 g (0.06 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Anotácia textu normy ASTM C150/C150M-22 :
Keywords:
hydraulic cement, portland cement, specification,, ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||
|
1.1?This specification covers ten types of portland cement, as follows (see Note 2): 1.1.1?Type IFor general use, when the special properties specified for any other type are not required. 1.1.2?Type IAAir-entraining cement for the same uses as Type I, where air-entrainment is desired. 1.1.3?Type IIFor general use, more especially when moderate sulfate resistance is desired. 1.1.4?Type IIAAir-entraining cement for the same uses as Type II, where air-entrainment is desired. 1.1.5?Type II(MH)For general use, more especially when moderate heat of hydration and moderate sulfate resistance are desired. 1.1.6?Type II(MH)AAir-entraining cement for the same uses as Type II(MH), where air-entrainment is desired. 1.1.7?Type IIIFor use when high early strength is desired. 1.1.8?Type IIIAAir-entraining cement for the same use as Type III, where air-entrainment is desired. 1.1.9?Type IVFor use when a low heat of hydration is desired. 1.1.10?Type VFor use when high sulfate resistance is desired. Note 1:?Some cements are designated with a combined type
classification, such as Type I/II, indicating that the cement meets
the requirements of the indicated types and is being offered as
suitable for use when either type is desired.
Note 2:?Cement conforming to the requirements for all types
are not carried in stock in some areas. In advance of specifying
the use of cement other than Type I, determine whether the proposed
type of cement is or can be made available.
1.2?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10, of measurements made in other units [or SI units]. Values are stated in only SI units when inch-pound units are not used in practice. 1.3?The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
