Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM C1439-13

Standard Test Methods for Evaluating Latex and Powder Polymer Modifiers for use in Hydraulic Cement Concrete and Mortar

Automaticky preložený názov:

Štandardné skúšobné metódy pre hodnotenie Latex a prášok Polymérne modifikátory pre použitie v hydraulických cementáreň betónu a malty

NORMA vydaná dňa 1.10.2013

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 79.90 € Tlačené - 79.90 €
Dostupnosť	SKLADOM
Cena	79.90 € bez DPH
79.90 €

Informácie o norme:

Označenie normy: ASTM C1439-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.10.2013
Kód tovaru: NS-11290
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Cement. Sádra. Vápno. Malta

Anotácia textu normy ASTM C1439-13 :

Keywords:

latex, latex polymer, polymer-modified concrete, polymer-modified mortar, powder polymer, ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)

Doplňujúce informácie


Significance and Use
3.1 These test methods are used to develop data for comparison with the requirements of Specification C1438. Standardized procedures are used to compare the properties of specimens made from test mixtures of polymer-modified concrete or mortar with the properties of specimens made from reference mixtures. These test methods are not intended to simulate job conditions.

1. Scope
1.1 These test methods provide a means of determining the effect of adding polymer modifiers to reference concrete or mortar. 1.2 Most sections of ASTM test methods and practices for hydraulic cement mortar and concrete apply to the preparation and testing of specimens made with polymer-modifiers. However, there are some exceptions, most notably curing, that need special procedures in order to develop the properties inherent with polymer-modification. These test methods cover these exceptions. 1.3 For testing polymer-modified mortar and concrete specimens, the procedures in this standard supersede those in the referenced ASTM test methods and practices. These test methods are not applicable to dry, packaged mortar and concrete. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
C33-07	Standard Specification for Concrete Aggregates
C127-15	Standard Test Method for Relative Density (Specific Gravity) and Absorption of Coarse Aggregate (Withdrawn 2024)
C128-22	Standard Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate
C150-07	Standard Specification for Portland Cement
C192/C192M-19	Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory
C260-10	Standard Specification for Air-Entraining Admixtures for Concrete
C403/C403M-23	Standard Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance
C778-21	Standard Specification for Standard Sand
C1437-20	Standard Test Method for Flow of Hydraulic Cement Mortar
C305-20	Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency
C494/C494M-19e1	Standard Specification for Chemical Admixtures for Concrete (Includes all amendments and changes 8/11/2022).
C1202-22e1	Standard Test Method for Electrical Indication of Concrete’s Ability to Resist Chloride Ion Penetration (Includes all amendments and changes 6/27/2022).
C1404-C1404M-98	Standard Test Method for Bond Strength of Adhesive Systems Used with Concrete as Measured by Direct Tension
C1438-13(2017)	Standard Specification for Latex and Powder Polymer Modifiers for use in Hydraulic Cement Concrete and Mortar
C39/C39M-23	Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens
C109/C109M-23	Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 50?mm [2 in.] Cube Specimens)
C138/C138M-23	Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete
C143/C143M-20	Standard Test Method for Slump of Hydraulic-Cement Concrete
C173/C173M-24	Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method
C185-20	Standard Test Method for Air Content of Hydraulic Cement Mortar
C231-09	Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method