Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Practice for Molding Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Hammer
Automaticky preložený názov:
Štandardná prax pre liatie Roller - hutného betónu do valcov lisovacie forma pomocou vibračného Hammer
NORMA vydaná dňa 1.6.2008
Označenie normy: ASTM C1435/C1435M-08
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.6.2008
Kód tovaru: NS-11273
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Keywords:
compressive, consolidate, cylinder, molds, roller compacted concrete, soil cement, specimen, strength, tensile, vibrating hammer, Cylindrical concrete specimens, Roller-compacted concrete, Vibrating hammer, ICS 91.100.30
Significance and Use | ||||||||||||||||||
This practice, intended for use in testing roller-compacted concrete, may be applicable to testing other types of cementitious material such as coarse-grained, soil-cement. This practice provides standardized requirements for molding stiff to very dry consistency concrete mixtures commonly used in roller compacted concrete construction. This practice is used instead of rodding or internal vibration, which cannot properly consolidate concrete of this consistency (Note 1). Note 1—Further description of roller compacted concrete consistency is given in ACI 207.5R and 211.3. The consistency of concrete using a vibrating table may be determined in accordance with Test Methods C 1170. This practice is used to mold cylindrical test specimens commonly used for testing compressive or tensile strength of concrete. Specimens tested for compressive strength and splitting tensile strength shall be in accordance with Test Methods C 39/C 39M and C 496/C 496M, respectively. Test specimens also may be used to determine density of fresh concrete. Specimens tested for density of fresh concrete shall be in accordance with Test Methods C 1170. Note 2—For some extremely dry mixtures; (those with a consistency greater than 45 s when tested in accordance with Test Methods C 1170) the density of specimens made in accordance with this practice may be greater than the in-place density of roller-compacted concrete due to the greater potential for voids at the bottom of the lifts in the field. |
||||||||||||||||||
1. Scope | ||||||||||||||||||
1.1 This practice covers molding cylindrical test specimens from concrete when the standard procedures of rodding and internal vibration, as described in Practice C 31/C 31M and Practice C 1176, are not practicable. This practice is applicable to freshly-mixed concrete, prepared in the laboratory and the field. 1.2 Freshly-mixed concrete is molded in cylindrical molds using an electric vibrating hammer equipped with a shaft and circular plate. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The text of this practice references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this practice. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||
|
Posledná aktualizácia: 2024-11-03 (Počet položiek: 2 209 203)
© Copyright 2024 NORMSERVIS s.r.o.