Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM C1410-13

Standard Specification for Cellular Melamine Thermal and Sound-Absorbing Insulation

Automaticky preložený názov:

Štandardné špecifikácie pre mobilné Melamín tepelnú a zvukovú absorbujúci Izolácia

NORMA vydaná dňa 15.5.2013

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 66.90 € Tlačené - 66.90 €
Dostupnosť	SKLADOM
Cena	66.90 € bez DPH
66.90 €

Informácie o norme:

Označenie normy: ASTM C1410-13
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.5.2013
Kód tovaru: NS-11129
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM C1410-13 :

Keywords:

acoustical insulation, formaldehyde and aldehyde, melamine, melamine formaldehyde, pipe insulation, thermal conductivity, thermal insulation, ICS Number Code 91.100.60 (Thermal and sound insulating materials)

Doplňujúce informácie

1. Scope

1.1 This specification covers the type, physical properties, and dimensions of open-cell melamine foam intended for use as thermal and sound-absorbing insulation for temperatures from −40 to +350°F (−40 to +177°C) in industrial environments.

1.2 Some uses of thermal insulation materials covered by this specification are governed by building codes that address fire performance.

1.3 The use of an appropriate vapor retarder is required on cold surface applications where water vapor condense and cause a decrease in thermal performance. Refer to Practice C755 for selection of vapor retarders. Facings shall be agreed upon between the purchaser and the manufacturer or supplier.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

C168-22	Standard Terminology Relating to Thermal Insulation
C177-19e1	Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus (Includes all amendments and changes 2/23/2023).
C335-05a	Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation
C356-22	Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat
C585-22	Standard Practice for Inner and Outer Diameters of Thermal Insulation for Nominal Sizes of Pipe and Tubing
C755-20	Standard Practice for Selection of Water Vapor Retarders for Thermal Insulation
C1045-19	Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
C518-21	Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
C423-23	Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method
C390-08(2019)	Standard Practice for Sampling and Acceptance of Thermal Insulation Lots
C1104/C1104M-19	Standard Test Method for Determining the Water Vapor Sorption of Unfaced Mineral Fiber Insulation
D3574-17	Standard Test Methods for Flexible Cellular Materials´Slab, Bonded, and Molded Urethane Foams
E84-23d	Standard Test Method for Surface Burning Characteristics of Building Materials (Includes all amendments and changes 1/29/2024).
E176-24	Standard Terminology of Fire Standards
E662-21ae1	Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials (Includes all amendments and changes 9/16/2021).
E795-23	Standard Practices for Mounting Test Specimens During Sound Absorption Tests
E2231-21	Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics
Boeing Specification Support Standard 72396 The Boeing Company, Boeing Technology Services, Seattle, WA, http://www.boeing.com.
C1363-19	Standard Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus
D2863-23	Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index)

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.