Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM C1374-14

Standard Test Method for Determination of Installed Thickness of Pneumatically Applied Loose-Fill Building Insulation

Automaticky preložený názov:

Štandardná skúšobná metóda pre stanovenie Inštalovaný Hrúbka pneumaticky aplikovanej voľne sypané izolácie budov

NORMA vydaná dňa 15.4.2014

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 68.80 € Tlačené - 68.80 €
Dostupnosť	SKLADOM
Cena	68.80 € bez DPH
68.80 €

Informácie o norme:

Označenie normy: ASTM C1374-14
Poznámka: NEPLATNÁ
Dátum vydania normy: 15.4.2014
Kód tovaru: NS-10916
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Tepelně a zvukově izolační materiály
Tepelné izolace

Anotácia textu normy ASTM C1374-14 :

Keywords:
cellulose, cellulosic fiber, fibrous glass, installed thickness, insulation, loose fill, mineral fiber, pneumatically applied, thermal insulation, thickness, ICS Number Code 91.100.60 (Thermal and sound insulating materials), 91.120.10 (Thermal insulation of buildings)

Doplňujúce informácie

Significance and Use

5.1 This test method was designed to give the manufacturer of loose-fill insulation products a way of determining what the initial installed thickness should be in a horizontal open attic for pneumatic applications.

5.2 The installed thickness value developed by this test method is intended to provide guidance to the installer in order to achieve a minimum mass/unit area for a given R-value.

5.3 For the purpose of product design, testing should be done at a variety of R-values. At least three R-values should be used: the lowest R-value on the product label, the highest R-value on the product label, and an R-value near the midpoint of the R-value range.

5.4 Specimens are blown in a manner consistent with the intended installation procedure. Blowing machine settings should be representative of those typically used for field application with that machine.

5.5 The material blown for a given 1.1 This test method covers determination of the installed thickness of pneumatically applied loose-fill building insulations prior to settling by simulating an open attic with horizontal blown applications.

1.2 This test method is a laboratory procedure for use by manufacturers of loose-fill insulation for product design, label development, and quality control testing. The apparatus used produces installed thickness results at a given mass/unit area.

1.3 This test method is not the same as the design density procedures described in Test Methods C520 or Specifications C739 or C764.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

C168-22	Standard Terminology Relating to Thermal Insulation
C520-15(2020)	Standard Test Methods for Density of Granular Loose Fill Insulations
C739-21a	Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation (Includes all amendments and changes 9/17/2021).
C764-19	Standard Specification for Mineral Fiber Loose-Fill Thermal Insulation
E691-23	Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method