Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM C1184-23

Standard Specification for Structural Silicone Sealants

NORMA vydaná dňa 1.5.2023

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 50.90 € PDF + redline - ihneď - 61.10 € Tlačené - 50.90 € Tlač + redline - 61.10 €
Dostupnosť	SKLADOM
Cena	50.90 € bez DPH
50.90 €

Informácie o norme:

Označenie normy: ASTM C1184-23
Dátum vydania normy: 1.5.2023
Kód tovaru: NS-1144996
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Pojiva. Těsnicí materiály

Anotácia textu normy ASTM C1184-23 :

This specification describes the properties of cold liquid applied, single-component or multicomponent, chemically curing elastomeric structural silicone sealants herein referred to as the sealant. These sealants are intended to structurally adhere components of structural sealant glazing systems. Sealants shall be classified as to types and uses: Type S; Type M; Use G; and Use O. The physical, mechanical, and performance properties of the sealant shall conform to the requirements described. The following test methods shall be performed: rheological properties; extrudability; hardness; heat aging; tack-free time; tensile adhesion; and shelf life.

Keywords:
ICS Number Code 91.100.50 (Binders. Sealing materials)

Doplňujúce informácie

1. Scope

1.1?This specification covers the properties of cold liquid applied, single-component or multicomponent, chemically curing elastomeric structural silicone sealants herein referred to as the sealant. These sealants are intended to structurally adhere components of structural sealant glazing systems.

1.2?Only those properties for which there are industry-agreed-upon minimum acceptable requirements, as determined by available ASTM test methods, are described in this specification. Additional properties may be added as ASTM test methods for those properties become available.

1.3?The values stated in metric (SI) units are to be regarded as the standard. The values in parentheses are for information only.

1.4?Committee C24, with jurisdiction over this specification, is aware of two comparable standards by other organizations: ETAG No. 002 and the Chinese national standard GB16776.

Note 1:?ETAG 002 is currently no longer supported.

1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

G151-19	Standard Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources
G154-23	Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Materials
G155-21	Standard Practice for Operating Xenon Arc Lamp Apparatus for Exposure of Materials
ETAG No. 002	Guideline for European Technical Approval for Structural Sealant Glazing Systems
C792-23	Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants
C794-18(2022)	Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants
C1087-23	Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
C639-15(2020)	Standard Test Method for Rheological (Flow) Properties of Elastomeric Sealants
C661-15(2022)	Standard Test Method for Indentation Hardness of Elastomeric-Type Sealants by Means of a Durometer
C679-15(2022)	Standard Test Method for Tack-Free Time of Elastomeric Sealants
C717-19	Standard Terminology of Building Seals and Sealants
C1135-19	Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
C1401-23	Standard Guide for Structural Sealant Glazing
C1442-14(2021)	Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus
C603-14(2019)	Standard Test Method for Extrusion Rate and Application Life of Elastomeric Sealants

Odporúčame:

Aktualizácia technických noriem

Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.

Chcete vedieť viac informácií ? Pozrite sa na túto stránku.

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.