Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM C1048-18
Standard Specification for Heat-Strengthened and Fully Tempered Flat Glass
NORMA vydaná dňa 1.10.2018
Informácie o norme:
Označenie normy: ASTM C1048-18
Dátum vydania normy: 1.10.2018
Kód tovaru: NS-904710
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Kategórie - podobné normy:
Anotácia textu normy ASTM C1048-18 :
This specification covers heat-treated flat glass - kind HS, kind FT coated and uncoated glass used in general building construction. Glass furnished under this specification shall be of the following conditions: condition A - uncoated surfaces, condition B - spandrel glass, one surface ceramic coated, and condition C - other coated glass. Flat glass furnished under this specification shall be of the following kinds: kind HS - heat-strengthened glass shall be flat glass, either transparent or patterned, in accordance with the applicable requirements, and kind FT - fully tempered glass shall be flat glass, either transparent or patterned in accordance with the applicable requirements. All fabrication, such as cutting to overall dimensions, edgework, drilled holes, notching, grinding, sandblasting, and etching, shall be performed before strengthening or tempering and shall be as specified. Requirements for fittings and hardware shall be as specified. In heat-strengthened and fully tempered glass, a strain pattern, which is not normally visible, may become visible under certain light conditions. The support system and the amount of glass deflection for a given set of wind-load conditions must be considered for design purposes. Heat-treated flat glass cannot be cut after tempering. Heat-treated glass can be furnished with holes, notches, cutouts, and bevels. The expansion fit and porosity of the ceramic coating shall be tested to meet the requirements prescribed. Specimens for evaluation of resistance to alkali and acid shall be prepared and tested to meet the requirements prescribed.
Keywords:
edge compression, flat glass, heat-strengthened glass, heat-treated glass, surface compression, tempered glass ,, ICS Number Code 81.040.30 (Glass products)
Doplňujúce informácie
| 1. Scope | ||||||||||||||||||||||
|
1.1 This specification covers the requirements for monolithic flat heat-strengthened and fully tempered coated and uncoated glass produced on a horizontal tempering system used in general building construction and other applications. 1.2 This specification does not address bent glass, or heat-strengthened or fully tempered glass manufactured on a vertical tempering system. 1.3 The dimensional values stated in SI units are to be regarded as the standard. The units given in parentheses are for information only. 1.4 The following safety hazards caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||
|
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
