Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
Standard Specification for Powder Metallurgy (PM) Titanium and Titanium Alloy Structural Components
NORMA vydaná dňa 1.9.2022
Označenie normy: ASTM B988-18(2022)
Dátum vydania normy: 1.9.2022
Kód tovaru: NS-1084169
Počet strán: 4
Približná hmotnosť: 12 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
This specification covers powder metallurgy (PM) structural components fabricated from commercially pure (CP) (that is, unalloyed) titanium powder, pre-alloyed powders, and mixtures of elemental powders or mixtures of elemental powders and pre-alloyed powders. It addresses ordering information, materials and manufacture, chemical composition requirements, tensile requirements, physical properties, mechanical properties, dimensions, mass, permissible variations, sampling, inspection, and certification.
Keywords:
CIP, cold isostatic pressing, compaction, HIP, hot isostatic pressing, PIF, pneumatic isostatic forging, powder forging, powder metallurgy, powder roll compaction, pre-alloyed powder, sinter, structural components, Ti Grade 1, Ti Grade 2, Ti Grade 3, Ti Grade 4, Ti-6Al4V, Ti-6A1-6V-2Sn, Ti 3Al2.5V, titanium, titanium alloys, titanium powder,, ICS Number Code 77.160 (Powder metallurgy)
1. Scope | ||||||||||||||||||||||||||
1.1?This specification covers powder metallurgy (PM) structural components fabricated from: 1.1.1?Commercially pure (CP) (that is, unalloyed) titanium powder, 1.1.2?Pre-alloyed powders. 1.1.3?Mixtures of elemental powders or mixtures of elemental powders and pre-alloyed powders. 1.2?This specification covers: 1.2.1?Grade 1 PMUnalloyed titanium, 1.2.2?Grade 2 PMUnalloyed titanium, 1.2.3?Grade 3 PMUnalloyed titanium, 1.2.4?Grade 4 PMUnalloyed titanium, 1.2.5?Grade 5 PMTitanium alloy (6 % aluminum, 4 % vanadium), 1.2.6?Grade 9 PMTitanium alloy (3 % aluminum, 2.5 % vanadium), 1.2.7?Ti-6Al-4V PM Low Interstitial (LI), 1.2.8?Ti-6Al-6V-2Sn PM. 1.3?The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard. 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||
|
Poskytovanie aktuálnych informácií o legislatívnych predpisoch vyhlásených v Zbierke zákonov od roku 1945.
Aktualizácia 2x v mesiaci !
Chcete vedieť viac informácii ? Pozrite sa na túto stránku.
Posledná aktualizácia: 2024-09-13 (Počet položiek: 2 429 660)
© Copyright 2024 NORMSERVIS s.r.o.