Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Norma ASTM B967/B967M-18(2023) 15.4.2023 náhľad

Doplňujúce informácie

ASTM B967/B967M-18(2023)

Standard Specification for Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire

NORMA vydaná dňa 15.4.2023

Jazyk
Prevedenie	PDF - okamžité stiahnutie - 66.40 € Tlačené - 66.40 €
Dostupnosť	SKLADOM
Cena	66.40 € bez DPH
66.40 €

Informácie o norme:

Označenie normy: ASTM B967/B967M-18(2023)
Dátum vydania normy: 15.4.2023
Kód tovaru: NS-1142318
Počet strán: 5
Približná hmotnosť: 15 g (0.03 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Kategórie - podobné normy:

Výrobky z mědi

Anotácia textu normy ASTM B967/B967M-18(2023) :

This specification covers the requirements for copper-zinc-tin-bismuth alloy rod, bar and wire intended for use in plumbing application and drinking water system. The product shall be manufactured by such hot working, cold working, and annealing processes as to produce a uniform wrought structure in the finished product. Chemical analysis, tensile strength, hardness, and yield strength test methods shall be performed in accordance to the specified requirements.

Keywords:

bar, copper-zinc-tin-bismuth alloy, drinking water, hexagonal rod, plumbing, rectangular bar, round rod, shapes, UNS Alloy Nos. C49250, C49255, C49260, C49265, C49300, C49340, C49345, C49350, C49360, wire, wrought copper alloys,, ICS Number Code 77.150.30 (Copper products)

Doplňujúce informácie

1. Scope

1.1?This specification establishes the requirements for copper-zinc-tin-bismuth alloy rod, bar and wire of alloy UNS Nos. C49250, C49255, C49260, C49265, C49300, C49340, C49345, C49350, C49355, and C49360 intended for use in plumbing applications and drinking water systems.

1.2?Typically, rod and bar product made to this specification is furnished as straight lengths. Wire (H04) 0.08 in. to 0.3 in. [2 mm to 8 mm inclusive] is furnished in coil form, and H50 shapes.

1.3?UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4?The following safety hazard caveat pertains only to the test method(s) described in this specification.

1.4.1?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

B250/B250M-19	Standard Specification for General Requirements for Wrought Copper Alloy Wire
B846-19a	Standard Terminology for Copper and Copper Alloys (Includes all amendments and changes 8/8/2019).
E8/E8M-24	Standard Test Methods for Tension Testing of Metallic Materials
E54-80(1996)	Standard Test Methods for Chemical Analysis of Special Brasses and Bronzes (Withdrawn 2002)
E62-89(1996)	Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E92-23	Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials
E478-08(2017)	Standard Test Methods for Chemical Analysis of Copper Alloys
E527-23	Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
ISO No. 3110 (AA)	Copper AlloysDetermination of Aluminum as an Alloying ElementVolumetric Available from International Organization for Standardization (ISO), ISO Central Secretariat, BIBC II, Chemin de Blandonnet 8, CP 401, 1214 Vernier, Geneva, Switzerland, http://www.iso.org.
	Method for Determination of Bismuth in Copper and Copper Alloys Available from Japanese Standards Association (JSA), Mita MT Bldg., 3-13-12 Mita, Minato-ku, Tokyo 108-0073, Japan, http://www.jsa.or.jp.
B249/B249M-23	Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.