Cookies
Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov. Súhlas udelíte kliknutím na tlačidlo „OK“.
ASTM B90/B90M-12
Standard Specification for Magnesium-Alloy Sheet and Plate
Automaticky preložený názov:
Štandardné špecifikácie pre zliatiny horčíka plechy a dosky
NORMA vydaná dňa 1.11.2012
Informácie o norme:
Označenie normy: ASTM B90/B90M-12
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.11.2012
Kód tovaru: NS-8698
Počet strán: 8
Približná hmotnosť: 24 g (0.05 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM
Anotácia textu normy ASTM B90/B90M-12 :
Keywords:
ICS Number Code 77.120.20 (Magnesium and magnesium alloys)
Doplňujúce informácie
| 1. Scope | |||||||||||||
|
1.1 This specification covers magnesium alloys in sheet and plate form designated as shown in
|
Composition %A |
||||||||||||
|
|
Al |
Mn |
R.E. |
Zn |
Zr |
Ca |
Cu |
Fe |
Ni |
Si |
Each |
Total |
Mg |
|
AZ31B |
2.5-3.5 |
0.20-1.0 |
. . . |
0.6-1.4 |
. . . |
0.04 |
0.05 |
0.005 |
0.005 |
0.10 |
. . . |
0.30 |
Remainder |
1.2 The values stated in either
inch-pound or SI units are to be regarded separately as standards.
The SI units are shown in brackets or in separate tables or
columns. The values stated in each system are not exact
equivalents; therefore, each system must be used independent of the
other. Combining values from the two systems may result in
nonconformance with the specification.
1.3 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
|
|
MIL-STD-129 |
Marking for Shipment and Storage |
|
Fed. Std. No. 184 |
Identification Marking of Aluminum, Magnesium and Titanium |
|
Fed. Std. No. 123 |
Marking for Shipment (Civil Agencies) |
|
Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric) |
|
|
Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
|
|
Standard Test Method for Analysis of Magnesium and Magnesium Alloys by Atomic Emission Spectrometry |
|
|
Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
|
|
Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition |
Odporúčame:
Aktualizácia technických noriem
Chcete mať istotu, že používate len platné technické normy?
Ponúkame Vám riešenie, ktoré Vám zaistí mesačný prehľad o aktuálnosti noriem, ktoré používate.
Chcete vedieť viac informácií ? Pozrite sa na túto stránku.
