Pozor!

Vo Vašom prehliadači nie je aktuálne povolené spúšťanie Javascriptu. Je možné, že niektoré funkcie nebudú fungovať správne. Pre plnú funkčnosť internetového obchodu odporúčame povoliť Javascript. Tu sú inštrukcie ako povoliť JavaScript vo Vašom webovom prehliadači.

Zobrazovaná mena: €

Zobrazenie ceny: bez DPH

Doplňujúce informácie

ASTM B85/B85M-10e1

Standard Specification for Aluminum-Alloy Die Castings (Includes all amendments And changes 11/26/2013).

Automaticky preložený názov:

Štandardné špecifikácie pre hliníkové zliatiny Die Odliatky

NORMA vydaná dňa 1.11.2010

Jazyk
Prevedenie	Online zabezpečené PDF - 74.00 € Tlačené - 74.00 €
Dostupnosť	SKLADOM
Cena	74.00 € bez DPH
74.00 €

Informácie o norme:

Označenie normy: ASTM B85/B85M-10e1
Poznámka: NEPLATNÁ
Dátum vydania normy: 1.11.2010
Kód tovaru: NS-8403
Počet strán: 10
Približná hmotnosť: 30 g (0.07 libier)
Krajina: Americká technická norma
Kategória: Technické normy ASTM

Tlač

Odoslať známemu

Otázka

Anotácia textu normy ASTM B85/B85M-10e1 :

Keywords:

aluminum, die casting, ICS Number Code 77.150.10 (Aluminium products)

Doplňujúce informácie

1. Scope

1.1 This specification covers aluminum-alloy die castings of all compositions. Thirteen of the most commonly die cast alloy compositions are specified, designated as shown in Table 1.

1.2 This specification is not intended for aluminum-alloy die castings used in aerospace applications.

1.3 Alloy and temper designations are in accordance with ANSI H35.1/H35.1(M). The equivalent unified numbering system alloy designations are in accordance with Practice E527.

1.4 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.

1.5 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2.

1.6 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

2. Referenced Documents

B179-18	Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes
E607-02	Standard Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere
B557-15(2023)	Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
B557M-15(2023)	Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric)
B660-23	Standard Practices for Packaging/Packing of Aluminum and Magnesium Products
B881-25a	Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products (Includes all amendments and changes 1/8/2026).
B985-24	Standard Practice for Sampling Aluminum Ingots, Billets, Castings and Finished or Semi-Finished Wrought Aluminum Products for Compositional Analysis
D3951-18(2023)	Standard Practice for Commercial Packaging
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E8/E8M-25	Standard Test Methods for Tension Testing of Metallic Materials
E23-25	Standard Test Methods for Notched Bar Impact Testing of Metallic Materials
E716-16(2021)e2	Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry (Includes all amendments and changes 9/7/2022).
E1251-25	Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry
IEEE/ASTM SI 10	Standard for Use of the International System of Units (SI): The Modern Metric System
H35.1/H35.1(M)-2006	American National Standard Alloy and Temper Designation Systems for Aluminum Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
E34-11	Standard Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
E505-22	Standard Reference Radiographs for Inspection of Aluminum and Magnesium Die Castings
E527-23	Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
B275-14	Standard Practice for Codification of Certain Zinc, Tin and Lead Die Castings (Withdrawn 2020)

Doporučujeme:

Tu máte možnosť prispôsobiť si nastavenia súborov cookies v súlade s vlastnými preferenciami.

Potrebujeme váš súhlas na využitie jednotlivých dát, aby sa vám okrem iného mohli ukazovať informácie týkajúce sa vašich záujmov.